ChinaDrone.Request a quote ↗
COMPONENT

V40A 14S

By T-MOTOR ↗

The T-MOTOR V40A 14S is a FOC UAV electronic speed controller with PWM/CAN interfaces and separate input, output, signal and encoder cables. It supports 18–60V (6–14S), with a 20A continuous current rating and 40A peaks lasting less than 10 seconds. The controller measures 62 × 30 × 18mm and has no BEC.

Request a quote ↗
T-MOTOR V40A 14S electronic speed controller with silver finned housing and attached cables
T-MOTOR V40A 14S electronic speed controller with silver finned housing and attached cables
ModelV40A 14S
Controller typeFOC electronic speed controller
Dimensions62*30*18mm (L*W*H)
Weight including cables69gIncluding cables.
Additional weight figures50g (excl. Cable) /68g50g excludes cable.
Input cableSilicone Wire-Red/ Black-14AWG-150mm

Product overview

The T-MOTOR V40A 14S is a FOC electronic speed controller for UAV propulsion. It measures 62 × 30 × 18mm (L × W × H) and has separate input, output, signal and encoder cables. Its input cable uses red/black 14AWG silicone wire measuring 150mm, while the output uses orange 16AWG silicone wire measuring 65mm. Both the shielded signal cable and shielded encoder cable measure 300mm; the encoder cable uses 24AWG wiring and an M6 aviation connector.

The controller supports PWM/CAN and an 18–60V (6–14S) supply. Continuous current is 20A, with a 40A peak rating for durations below 10 seconds. Its throttle position range is 1040–1940μs, throttle refresh frequency is 50–500Hz, and throttle response speed is 300ms. Standby consumption is ≤50mA at 48V, and there is no BEC. Weight including cables is 69g; additional ESC weight figures are 50g excluding cable and 68g. The product is an ESC component with cabling.

Specifications

SpecificationValue & conditions
ModelV40A 14S
Controller typeFOC electronic speed controller
Dimensions62*30*18mm (L*W*H)
Weight including cables69gIncluding cables.
Additional weight figures50g (excl. Cable) /68g50g excludes cable.
Input cableSilicone Wire-Red/ Black-14AWG-150mm
Signal cableShielded Cables-Black- OD4.2-5C-300mm-JP- 3P*2-Black Blank White- Green Yellow Gray
Encoder cablesShielded Cables-Black-24AWG-5C-300mm-M6 Aviation Connector
Output cableSilicone Wire-Orange- 16AWG-65mm
Control protocolsPWM/CAN
Supported voltage18~60V (6~14S)
BECNO
Continuous current20AContinuous operation.
Peak current40ADuration less than 10s.
Throttle position range1040~1940μs
Throttle refresh frequency50~500Hz
Standby consumption≤50mA@48VAt 48V.
Throttle response speed300ms
SOURCE WITH CHINADRONE

Request a quote for V40A 14S

Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.

Submit your procurement requirements ↗

No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.

KEEP EXPLORING

Similar products

Browse all products ↗
Motors & ESCs

P80Ⅲ Pin Agricultural UAV Motor KV120

By T-MOTOR

The T-MOTOR P80Ⅲ Pin Agricultural UAV Motor KV120 is an enclosed agricultural drone propulsion motor supplied with a hardware pack. It weighs 649g including cable, supports 6-12S LiPo power and has an 18.2kg maximum thrust specification. Propeller installation requires an adapter, and maintenance includes regular bearing lubrication.

GEPRC TAKER F722 BLS 80A V2 STACK flight controller and ESC circuit board assembly
Flight control & navigation

GEPRC TAKER F722 BLS 80A V2 STACK

By GEPRC

The GEPRC TAKER F722 BLS 80A V2 STACK is a UAV electronics assembly combining an F722 flight controller and an 80A four-in-one ESC. It supports 3-6S LiPo power, direct DJI Air Unit connection and 30.5×30.5mm mounting. The stack configuration includes connection cables, a filter board, power wiring and mounting hardware.

Scorpion HKII-2221-2010KV motor with orange end caps, black housing, shaft and connector leads
Motors & ESCs

Scorpion HKII-2221-2010KV

By Scorpion

The Scorpion HKII-2221-2010KV is a 2010KV brushless motor primarily intended for helicopter and ducted fan applications. It combines CNC-machined aluminum alloy parts with a nine-arm stator and six magnet poles. The package includes connectors, heat shrink and mounting screws; propeller use requires a separately purchased shaft adapter.