Product overview
The GEPRC TAKER F722 BLS 100A 8S STACK combines a TAKER F722 8S flight controller with a TAKER H100_8S_BLS 100A 4IN1 ESC for UAV flight control and motor power management. STACK, FC and ESC configurations are offered. The controller uses an STM32F722 processor and an ICM42688-P IMU connected over SPI, with 16M onboard black box storage, barometer support and BetaFlight OSD through an AT7456E chip. This is an electronics assembly for integration into an aircraft.
Installation space must accommodate the 38.5×38.5mm flight controller and the larger 56.3*61.1 mm ESC. Both use a 30.5×30.5mm mounting pattern, with φ4mm holes reduced to φ3mm by the silicone shock absorbers. Integration interfaces include six UARTs, Type-C USB and a direct DJI Air Unit connection. Independent 5V@3A and 12V@3A BEC outputs and an integrated LC filter support peripheral power integration. Both boards accept 3-8S LiPo input; the ESC specifies 100A continuous current and 105A burst current for five seconds.
The stack package supplies both boards, a 50V 4700uF electrolytic capacitor, an XT90 battery plug, 10AWG power cable and connection cables for the DJI unit, flight controller, receiver, camera and VTX. Screws, nylon nuts and silicone anti-shake pads complete the installation hardware. The ESC supports Dshot 150/300/600 and uses target B_X_30. The current flight controller target is GEPRC_TAKER_F722_8S; using the older TAKERF722SE firmware requires the specified barometer definitions before flashing and the pinio_box CLI setting afterward.
Specifications
| Specification | Value & conditions |
|---|---|
| Product and configuration options | GEPRC TAKER F722 BLS 100A 8S STACK |
| Selectable configurations | STACK, FC, ESC |
| Legacy firmware flashing requirements | Add “USE_BARO USE_BARO_DPS310” before flashing; afterward enter “set pinio_box = 40,41,255,255” and “save” in the CLI.When flashing TAKERF722SE firmware. |
| Flight controller model | TAKER F722 8S Flight Controller |
| MCU | STM32F722 |
| IMU | ICM42688-P(SPI) |
| Black box storage | 16M onboard |
| OSD | BetaFlight OSD with AT7456E chip |
| Independent BEC outputs | 12V@3A and 5V@3A |
| Current flight controller firmware target | GEPRC_TAKER_F722_8S |
| Flight controller dimensions | 38.5×38.5mm |
| Flight controller mounting | 30.5×30.5mm mounting pattern; φ4mm holes, reduced to φ3mm with silicone shock-absorbing circlesHole diameter becomes φ3mm when the silicone shock-absorbing circle is fitted. |
| Flight controller input voltage | 3-8S LiPo |
| UART interfaces | 6 UARTs |
| Flight controller weight | 8.1g |
| ESC model | TAKER H100_8S_BLS 100A 4IN1 ESC |
| ESC input voltage | 3-8S Lipo |
| ESC current calibration value | 200 |
| ESC continuous current | 100A |
| ESC burst current | 105A (5 seconds)5 seconds. |
| ESC protocols | Dshot 150/300/600 |
| ESC dimensions and mounting | 56.3*61.1 mm; mounting pattern: 30.5×30.5 mm; φ4 mm holes reduced to φ3mm with silicone shock-absorbing ringsHole diameter becomes φ3mm when the silicone shock-absorbing ring is fitted. |
| ESC weight | 28.8g |
| ESC firmware target | B_X_30 |
| Air Unit connection | Direct plug connection to DJI Air Unit |
| USB interface | Type-C |
| Barometer support | Supported |
| Power filtering | Integrated LC filter |
| ESC ammeter support | Supported |
| Supplied equipment | 1 × TAKER F722 8S Flight Controller; 1 × TAKER H100_8S_BLS 100A 4IN1 ESC; 1 × 50V 4700uF electrolytic capacitor; 1 × DJI cable (SH1.0 6pin 100mm); 2 × FC adapter cables (SH1.0 8pin 30mm); 1 × receiver silicone cable (SH1.0 4pin 150mm); 1 × camera cable (SH1.0-SH1.25 3pin 135mm); 1 × VTX cable (SH1.0 4pin-6pin 100mm); 1 × XT90 battery plug; 1 × red and black power cable (10AWG 240mm); 4 × M3*30 screws; 4 × M3*25 screws; 8 × M3 nylon nuts; 12 × M3 silicone anti-shake padsSTACK configuration. |
Request a quote for GEPRC TAKER F722 BLS 100A 8S STACK
Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.
Submit your procurement requirements ↗No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.
