Product overview
The GEPRC TAKER F722 BL32 E55A SE STACK combines a TAKER F722 SE flight controller with a TAKER E55_96K BL32 four-in-one ESC for racing UAV builds. Its controller uses an STM32F722RET6 processor, ICM42688-P IMU and 32Mb flash for black-box recording. The controller measures 31.7×31.5mm and weighs 6.0g, while the ESC weighs 9.6g. A 25.5×25.5mm mounting pattern provides the installation interface; the 4mm holes accept supplied vibration-reduction silicone adapters for 3mm or 2mm screws. The stack arrangement also assists heat dissipation from the controller and MOS devices.
Integration options include soldered wiring, SH1.0 terminals, receiver and analog-camera connections, and a direct DJI Air Unit connection. Independent BEC channels provide 10V 2A and 5V 2.5A outputs. Both boards accept 2–6S LiPo input, and UART 6 is reserved for the ESC. The supplied electronics set includes the controller, ESC, capacitor, power lead, interconnects, peripheral cables and mounting hardware. The ESC specification lists 55A continuous and 60A for five seconds; separate descriptive measured figures are lower at 50A continuous and 55A instantaneous.
Specifications
| Specification | Value & conditions |
|---|---|
| Product and purpose | GEPRC TAKER F722 BL32 E55A SE STACK |
| Architecture and application | Flight-controller and ESC stack for racing UAV integration. |
| MCU | STM32F722RET6TAKER F722 SE FC |
| IMU | ICM42688-PTAKER F722 SE FC |
| Black box | 32Mb FlashTAKER F722 SE FC |
| USB | Type-CTAKER F722 SE FC |
| OSD | BetaFlight OSD w / AT7456E chipTAKER F722 SE FC |
| BEC outputs | Independent dual-channel BEC: 10V 2A and 5V 2.5A.TAKER F722 SE FC |
| Firmware target | TAKERF722SETAKER F722 SE FC |
| Dimensions | 31.7×31.5mmTAKER F722 SE FC |
| Mounting holes | 25.5×25.5mm mounting pattern; φ4mm holes.TAKER F722 SE FC; vibration-reduction silicone adapts the mounting holes for 3mm or 2mm screws. |
| Input voltage | 7.4V – 25.2V (LiPo 2-6S)TAKER F722 SE FC; LiPo 2-6S. |
| UART | 6 UARTSTAKER F722 SE FC; UART 6 is for the ESC only. |
| Power filter | Integrated LC filterTAKER F722 SE FC |
| Weight | 6.0gTAKER F722 SE FC |
| Input voltage | 7.4V-25.2V (LiPo 2-6S)TAKER E55_96K BL32 4IN1 ESC 55A; LiPo 2-6S. |
| Galvanometer | SupportedTAKER E55_96K BL32 4IN1 ESC 55A |
| PWM refresh frequency | 24K-96KTAKER E55_96K BL32 4IN1 ESC 55A |
| Continuous current | 55ATAKER E55_96K BL32 4IN1 ESC 55A |
| Burst current | 60A (5s)TAKER E55_96K BL32 4IN1 ESC 55A; 5s burst. |
| Telemetry | SupportedTAKER E55_96K BL32 4IN1 ESC 55A |
| Supported protocols | Oneshot125 / Oneshot42 / Mulishot modes Dshot 150/300/600TAKER E55_96K BL32 4IN1 ESC 55A |
| Firmware target | ST_G0_05TAKER E55_96K BL32 4IN1 ESC 55A |
| Weight | 9.6gTAKER E55_96K BL32 4IN1 ESC 55A |
| Measured current figures | Measured continuous overcurrent: 50A; instantaneous current: 55A.TAKER E55_96K BL32 4IN1 ESC 55A; descriptive measured-current figures. |
| Flight-controller wiring | Soldered connections and SH1.0 plug-in terminals. |
| Peripheral integration | Receiver and analog-camera support, with direct DJI Air Unit plug-in connection. |
| Thermal architecture | Stack arrangement assists heat dissipation from the main controller and MOS devices. |
| Included equipment | 1 flight controller; 1 ESC; 1 35V 470uf capacitor; 1 XT60 power cord; 1 8pin flight-controller-to-ESC cable; 4 M3*22 screws; 6 M3 anti-slip nuts; 12 vibration-reduction silicone adapters from 4mm to 3mm; 12 adapters from 4mm to 2mm; 1 65mm camera lens cable; 1 25mm camera lens cable; 1 receiver cable; 1 DJI Air Unit cable connector.Supplied configuration. |
Request a quote for GEPRC TAKER F722 BL32 E55A SE STACK
Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.
Submit your procurement requirements ↗No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.
