Product overview
The GEPRC TAKER F405 BLS 80A V2 STACK combines the GEP-F405-HD V3 flight controller with a TAKER H80_BLS 80A four-in-one ESC for UAV flight control and motor drive. The controller uses an STM32F405 processor, an ICM42688-P SPI inertial sensor and 16M onboard black-box storage. Integration connections include six UARTs, M1–M6 motor outputs, Type-C USB and a direct DJI Air Unit connection. BetaFlight OSD uses an AT7456E chip, while the controller also provides an integrated LC filter and support for a barometer.
Installation space must accommodate the 37.15×37.15mm controller and the larger 56.3*61.1mm ESC. Both use 30.5×30.5mm mounting patterns, with 4mm holes reduced to 3mm through silicone isolation inserts. Both boards accept 3–6S LiPo input; the ESC specifies 80A continuous current and an 85A burst limited to five seconds. The stack configuration includes both boards, a dual 50V 2200uF filter board, connection cables, an XT90 plug, power wiring and mounting hardware. STACK, FC and ESC are separate configuration choices for procurement.
Specifications
| Specification | Value & conditions |
|---|---|
| Product options | STACK, FC, ESC |
| FC model | GEP-F405-HD V3 Flight ControllerFlight controller. |
| MCU | STM32F405Flight controller. |
| IMU | ICM42688-P(SPI)Flight controller. |
| Black box | 16M onboardFlight controller. |
| Motor outputs | M1-M6Flight controller. |
| OSD | BetaFlight OSD w/ AT7456E chipFlight controller. |
| BEC | 5V@3A, [email protected] dual BECFlight controller. |
| Firmware target | GEPRCF405Flight controller. |
| FC dimensions | 37.15×37.15mmFlight controller. |
| FC mounting | 30.5×30.5mm, φ4mm hole becomes φ3mm after using a silicone shock-absorbing circleFlight controller; hole diameter reduces with the silicone shock-absorbing circle installed. |
| FC input voltage | 3-6S LiPoFlight controller. |
| UART | 6 UARTsFlight controller. |
| FC weight | 7.3gFlight controller. |
| ESC model | TAKER H80_BLS 80A 4IN1 ESC |
| ESC input voltage | 3-6S LipoESC. |
| Continuous current | 80AESC. |
| Burst current | 85A (5 second)ESC; 5-second burst. |
| Supported protocol | Dshot 150/300/600ESC. |
| ESC dimensions and mounting | 56.3*61.1mm, hole30.5×30.5mm, φ4mm hole becomes φ3mm after using the silicone shock-absorbing ring.ESC; hole diameter reduces with the silicone shock-absorbing ring installed. |
| ESC weight | 28.1gESC. |
| ESC target | B_X_30ESC. |
| Air Unit connection | Direct plugging into DJI Air UnitFlight controller. |
| Barometer support | SupportedFlight controller. |
| USB interface | Type-CFlight controller. |
| Power filter | Integrated LC filterFlight controller. |
| Ammeter support | SupportedESC. |
| Included electronics | 1 × GEP-F405-HD V3 Flight Controller; 1 × TAKER H80_BLS 80A 4IN1 ESC; 1 × filter board (Dual 50V 2200uF).Stack configuration. |
| Included wiring and battery connector | 1 × DJI connection cable (SH1.0 6pin 100mm); 1 × FC adapter cable (SH1.0 8pin 30mm); 1 × receiver silicone cable (SH1.0 4pin 150mm); 1 × camera connection cable (SH1.0-SH1.25 3pin 60mm); 1 × VTX connection cable (SH1.0 4pin-6pin 100mm); 1 × XT90 battery plug; 1 × red and black power cable (10AWG 240mm).Stack configuration. |
| Included mounting hardware | 4 × M3*30 screws; 4 × M3*25 screws; 8 × nylon nuts (M3); 12 × silicone anti-shake pads (M3).Stack configuration. |
Request a quote for GEPRC TAKER F405 BLS 80A V2 STACK
Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.
Submit your procurement requirements ↗No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.
