Product overview
The GEPRC TAKER F722 BT 8Bit 60A STACK combines a GEP-F722-BT-HD V3 flight controller with a TAKER H60_BLS 60A four-in-one ESC for UAV control and motor-drive integration. The controller uses an STM32F722 processor and ICM42688-P SPI IMU, with a barometer, 512M onboard black box storage and an integrated LC power filter. Type-C USB, an AT7456E-based BetaFlight OSD and a direct DJI Air Unit connection provide interfaces for configuration and video-system integration. Five UART groups are specified, with UART4 fixed for Bluetooth.
Integration requires space for the 36.9×36.9mm controller and 42×45.7mm ESC, both using a 30.5×30.5mm mounting pattern. Silicone shock-absorbing rings reduce the mounting-hole diameter from φ4mm to φ3mm. Both boards accept 3–6S LiPo input; the ESC specifies 60A continuous current and a 65A burst for five seconds. Supplied equipment includes both boards, a capacitor, connection and power cables, screws, nuts and silicone pads. This is an electronics stack for installation in a UAV. The current batch does not support Bluetooth wireless parameter tuning.
Specifications
| Specification | Value & conditions |
|---|---|
| Manufacturer and model | GEPRC TAKER F722 BT 8Bit 60A STACK |
| Stack architecture | GEP-F722-BT-HD V3 flight controller paired with TAKER H60_BLS 60A 4IN1 ESC |
| Flight controller MCU | STM32F722 |
| Flight controller IMU | ICM42688-P(SPI) |
| Black box storage | 512M onboard |
| OSD | BetaFlight OSD w/ AT7456E chip |
| Flight controller BEC | 5V@3A, [email protected] dual BEC |
| Flight controller firmware target | GEPRCF722_BT_HD_V3 |
| Flight controller dimensions and mounting | 36.9×36.9mm; mounting pattern 30.5×30.5mm; φ4mm holes become φ3mm with silicone shock-absorbing ringsMounting holes become φ3mm when silicone shock-absorbing rings are used. |
| Flight controller input voltage | 3-6S LiPo |
| Flight controller UARTs | 5 groups (UART4 fixed for Bluetooth)UART4 is fixed for Bluetooth. |
| Flight controller weight | 8.2g |
| ESC input voltage | 3-6S Lipo |
| ESC continuous current | 60A |
| ESC burst current | 65A (5 second)5-second burst. |
| ESC control protocols | Dshot 150/300/600 |
| ESC dimensions and mounting | 42×45.7mm; mounting pattern 30.5×30.5mm; φ4mm holes become φ3mm with silicone shock-absorbing ringsMounting holes become φ3mm when silicone shock-absorbing rings are used. |
| ESC weight | 14.9g |
| ESC target | B_X_30 |
| Air Unit connection | Direct plug connection to the DJI Air Unit |
| Bluetooth limitation | Current batch does not support Bluetooth wireless parameter tuningCurrent batch affected by temporary hardware adjustments, as stated in the February 25, 2026 update. |
| Barometer | Supported |
| USB interface | Type-C |
| Power filter | Integrated LC filter |
| ESC current measurement | Supported |
| Included electronics and cables | 1 × FC board; 1 × ESC board; 1 × capacitor; 1 × O3 3-in-1 connection cable; 1 × FC adapter cable; 1 × sh1.0 4pin silicone cable; 1 × camera connection cable; 1 × VTX connection cable; 1 × XT90 power cableSupplied stack configuration. |
| Included mounting hardware | 4 × M3*30 screws; 4 × M3*25 screws; 8 × nylon nuts; 12 × silicone anti-shake padsSupplied stack configuration. |
Request a quote for TAKER F722 BT 8Bit 60A STACK
Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.
Submit your procurement requirements ↗No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.
