Product overview
The GEPRC TAKER F405 BLS 100A 8S STACK combines a GEP-F405-8S flight controller with a TAKER H100_8S_BLS 100A four-in-one ESC for UAV control and motor integration. It is an electronics assembly, with STACK, FC and ESC configuration options. The controller uses an STM32F405 MCU and ICM42688-P SPI IMU, with 16M onboard black box storage. Integration interfaces include six UARTs, M1–M8 motor outputs, Type-C USB and a direct DJI Air Unit connection. Power provisions include an integrated LC filter and dual 5V@3A and 12V@3A BEC outputs.
Installation space must accommodate the 37x37mm controller and larger 56.3*61.1mm ESC. Both use a 30.5×30.5mm mounting pattern, with φ4mm holes reduced to φ3mm by silicone isolation rings. Each board accepts 3-8S LiPo input; the ESC specifies 100A continuous current and a 105A burst limited to five seconds. The stack package includes both boards, a 50V 4700uF capacitor, connection cables, XT90 plug, power cable and mounting hardware. The current controller firmware target is GEPRCF405_8S; using GEPRCF405_BT_HD requires the specified CLI configuration after flashing.
Specifications
| Specification | Value & conditions |
|---|---|
| Configuration options | STACK, FC, ESC |
| Flight controller firmware change and legacy configuration | Current firmware: GEPRCF405_8S. After flashing GEPRCF405_BT_HD, enter these CLI commands in order: resource SERIAL_TX 11 NONE; resource SERIAL_RX 11 NONE; set pinio_config = 1,1,1,1; set pinio_box = 32,41,255,255; save.When flashing GEPRCF405_BT_HD firmware. |
| Flight controller model | GEP-F405-8S Flight Controller |
| Flight controller MCU | STM32F405 |
| Flight controller IMU | ICM42688-P(SPI) |
| Black box storage | 16M onboard |
| Motor outputs | M1-M8 |
| OSD | BetaFlight OSD with AT7456E chip |
| BEC outputs | 5V@3A,12V@3A dual BEC |
| Flight controller firmware target | GEPRCF405_8S |
| Flight controller dimensions | 37x37mm |
| Flight controller mounting | 30.5×30.5mm mounting pattern; φ4mm holes, becoming φ3mm with silicone shock-absorbing circlesFlight controller holes reduce to φ3mm when silicone shock-absorbing circles are fitted. |
| Flight controller input voltage | 3-8S LiPo |
| UART interfaces | 6 UARTs |
| Flight controller weight | 8.3g |
| ESC model | TAKER H100_8S_BLS 100A 4IN1 ESC |
| ESC input voltage | 3-8S Lipo |
| ESC current calibration value | 200 |
| ESC continuous current | 100A |
| ESC burst current | 105A (5 second)5-second burst. |
| ESC control protocols | Dshot 150/300/600 |
| ESC dimensions and mounting | 56.3*61.1mm; 30.5×30.5mm mounting pattern; φ4mm holes, becoming φ3mm with silicone shock-absorbing ringsESC holes reduce to φ3mm when silicone shock-absorbing rings are fitted. |
| ESC weight | 28.8g |
| ESC firmware target | B_X_3 |
| Air Unit connection | Direct plugging into DJI Air Unit |
| USB interface | Type-C |
| Power filter | Integrated LC filter |
| Barometer support | Supported |
| ESC ammeter support | Supported |
| Included equipment | 1 × GEP-F405-8S flight controller; 1 × TAKER H100_8S_BLS 100A 4IN1 ESC; 1 × electrolytic capacitor (50V 4700uF); 1 × DJI connection cable (SH1.0 6pin 100mm); 2 × FC adapter cables (SH1.0 8pin 30mm); 1 × receiver silicone cable (SH1.0 4pin 150mm); 1 × camera connection cable (SH1.0-SH1.25 3pin 135mm); 1 × VTX connection cable (SH1.0 4pin-6pin 100mm); 1 × XT90 battery plug; 1 × red and black power cable (10AWG 240mm); 4 × M3*30 screws; 4 × M3*25 screws; 8 × M3 nylon nuts; 12 × M3 silicone anti-shake pads.STACK configuration. |
Request a quote for GEPRC TAKER F405 BLS 100A 8S STACK
Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.
Submit your procurement requirements ↗No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.
