ChinaDrone.Request a quote ↗
COMPONENT

DYS XMS30A mini version ESC

By DYS ↗

The DYS XMS30A mini version ESC is a compact electronic speed controller for high-KV multirotor racing motors. Its 32 × 15 mm board integrates solder pads and a capacitor, with BLHeli firmware and Oneshot125/Multishot support. It accepts 3-6s LiPo power and has no BEC.

Request a quote ↗
DYS XMS30A mini version electronic speed controller with attached wires
DYS XMS30A mini version electronic speed controller with attached wires
Input voltage3-6s LiPoListed specification for the XMS30A mini version.
BECNoneListed specification for the XMS30A mini version.
Product identityDYS XMS30A mini version ESC
Intended applicationElectronic speed controller for high-KV racing motors
Dimensions32 mm long × 15 mm wide
Weight9.26 g

Product overview

The DYS XMS30A mini version ESC is a motor-control component for multirotor racing installations using high-KV brushless motors. Its compact board measures 32 mm long by 15 mm wide and weighs 9.26 g, giving integrators concrete dimensions for allocating installation space. Integrated solder pads support direct wiring, while a built-in capacitor forms part of the controller’s electrical configuration. The specified power input is 3-6s LiPo, and the controller has no BEC, a material constraint when planning power for onboard electronics.

The controller combines a Silabs F396 processor, BLHeli bootloader and firmware, and a MOS 7440 driver. Its throttle connection uses twisted-pair cable to reduce signal crosstalk, and its PCB design addresses impact resistance. Throttle signal refresh reaches up to 500 Hz, with 3000 Hz specified for Oneshot125; Multishot is also enabled. USB programming provides configuration access, including two-way and 3D modes. Named integration matches include DYS MR and SE racing motors and the Naze32 Rev6 and SP Racing F3 flight controllers.

Specifications

SpecificationValue & conditions
Input voltage3-6s LiPoListed specification for the XMS30A mini version.
BECNoneListed specification for the XMS30A mini version.
Product identityDYS XMS30A mini version ESC
Intended applicationElectronic speed controller for high-KV racing motors
Dimensions32 mm long × 15 mm wide
Weight9.26 g
Bootloader and firmwareBLHeli bootloader and firmware
MicroprocessorSilabs F396
Processor frequencyBasic frequency up to 50 MHz
DriverMOS 7440 driver
CapacitorBuilt-in capacitor
Connection architectureIntegrated solder pads
Throttle signal wiringTwisted-pair throttle signal cable
Power switching architectureMiniaturized, ultra-low-resistance MOSFET with dedicated MOS drive chips
PCB constructionPCB designed for improved impact resistance
Throttle signal refresh rateUp to 500 Hz
Oneshot125 refresh rate3000 HzOneshot125 operation.
Enabled signal protocolsOneshot125 and Multishot
Named flight controller compatibilityNaze32 Rev6 and SP Racing F3
Programming interfaceUSB programming
Operating modesTwo-way and 3D modes for high-speed racing and acrobatics
Matched motor familiesDYS MR and SE series brushless racing motors
SOURCE WITH CHINADRONE

Request a quote for DYS XMS30A mini version ESC

Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.

Submit your procurement requirements ↗

No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.

KEEP EXPLORING

Similar products

Browse all products ↗
Scorpion A2-4010-900kv motor with gold and black housing and an upright shaft
Motors & ESCs

Scorpion A2-4010-900kv (49" Acro / 4s / 1350w)

By Scorpion

The Scorpion A2-4010-900kv is an airplane propulsion motor supplied with mounting and connection accessories. It has a specified motor constant of 580 RPM / Volt and 950 Watts continuous power. Its 1350 Watts peak rating applies to intermittent full-throttle operation for 10–180 seconds, depending on use case and cooling; the rated LiPo configuration is 4s.

FLUXER PRO 16x5.4 in matte carbon fiber propeller pair with mounting hardware and packaging
Motors & ESCs

FLUXER PRO 16x5.4 in Matt Prop - 2Pcs

By MAD Components

The MAD FLUXER PRO 16x5.4 in Matt Prop - 2Pcs supplies one clockwise and one counterclockwise drone propeller. Carbon fiber prepreg construction incorporates a balsa wood core and matte finish. Integration details include a 6mm mounting hole and customizable hole positioning, with design emphasis on low-RPM performance.

5012 IPE V3.0 drone motor, 160KV variant, with black cylindrical housing and central shaft
Motors & ESCs

5012 IPE V3.0 Drone Motor

By MAD Components

The MAD 5012 IPE V3.0 Drone Motor is a propulsion component supporting 4S and 6S power, four KV options and 18–22 inch carbon fiber propellers. It provides 1.5–3.0kg sustained thrust and a 6.1kg short-term peak, with defined mounting interfaces, centrifugal heat dissipation and IP45 protection.

FS 2204 ELITE 1900KV FPV drone motor with red accents and threaded shaft
Motors & ESCs

FS 2204 ELITE FPV Drone motor

By MAD Components

The MAD FS 2204 ELITE FPV Drone motor is a freestyle brushless motor featuring a lightweight titanium shaft, 0.15mm silicon steel sheet and secondary anodizing. It measures D:27 × 29.9 mm, uses M5 nut propeller attachment, and offers 1900KV–6S, 2300KV–6S and 2750KV–4S options.