ChinaDrone.Request a quote ↗
COMPONENT

SwellPro ESC for Splashdrone 3+

By SwellPro ↗

The SwellPro ESC for Splashdrone 3+ is a compact 40A electronic speed controller for SplashDrones and custom drone integration. It supports 2-6-cell lithium batteries and 60A bursts lasting up to 10 seconds. Its OPTO configuration omits a BEC, requiring separate receiver power provision when the flight controller lacks one.

Request a quote ↗
SwellPro ESC for Splashdrone 3+ with attached wires and connectors
SwellPro ESC for Splashdrone 3+ with attached wires and connectors
Product identitySwellPro ESC for Splashdrone 3+
Intended application40A electronic speed controller optimized for SplashDrones.
Output currentContinuous 40A; burst 60A up to 10 seconds.Burst output limited to up to 10 seconds.
Input voltage2-6 cells lithium battery.Lithium battery input.
BEC configurationNo BEC.
Receiver power requirementA separately purchased 5V UBEC module is required to power the RC receiver.Flight controller has no included BEC.

Product overview

The SwellPro ESC for Splashdrone 3+ is an electronic speed controller optimized for SplashDrones, with provision for use in custom drone builds. Its circuits address reliability and heat dissipation, while multirotor control programming targets throttle response. Software is optimized for disc-type motors, and preset settings provide adaptive operation. The power stage uses extra-low-resistance MOSFETs. Continuous output is 40A, with a 60A burst permitted for up to 10 seconds, using a 2-6-cell lithium battery input.

The controller measures 68 x 25 x 8.7mm and weighs 26g, defining its installation space and component mass. It has 120mm red and black cables, a 260mm signal cable and a 3.5mm bullet connector specification. Its OPTO configuration has no BEC: installations whose flight controller lacks a BEC require a separately purchased 5V UBEC to power the RC receiver. Timing is High or Intermediate. The throttle refresh specification is at least 400Mhz, alongside a separately stated supported signal frequency of up to 621Hz.

Specifications

SpecificationValue & conditions
Product identitySwellPro ESC for Splashdrone 3+
Intended application40A electronic speed controller optimized for SplashDrones.
Output currentContinuous 40A; burst 60A up to 10 seconds.Burst output limited to up to 10 seconds.
Input voltage2-6 cells lithium battery.Lithium battery input.
BEC configurationNo BEC.
Receiver power requirementA separately purchased 5V UBEC module is required to power the RC receiver.Flight controller has no included BEC.
Throttle signal refresh rateAt least 400Mhz.
TimingHigh or Intermediate.
Red and black cable length120mm.
Signal cable length260mm.
Bullet connector3.5mm.
Dimensions68 x 25 x 8.7mm.
Weight26g.
Circuit designCircuits and functions optimized for reliability and heat dissipation.
Multirotor control programmingMultirotor controller programming intended to improve throttle response.
Motor software optimizationSoftware optimized for compatibility with disc-type motors.Disc-type motors.
Preset settingsAdaptive preset settings.
Signal crosstalk reductionDesigned to reduce crosstalk in signal transmission.
Supported control signal frequencyUp to 621Hz; compatibility with various flight-control systems.
MOSFET architectureMOSFET drive circuitry with extra-low-resistance MOSFETs.
SOURCE WITH CHINADRONE

Request a quote for SwellPro ESC for Splashdrone 3+

Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.

Submit your procurement requirements ↗

No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.

KEEP EXPLORING

Similar products

Browse all products ↗
GEPRC SPEEDX2 2306E 1860KV motor in black with threaded shaft and wires
Motors & ESCs

GEPRC SPEEDX2 2306E Motor

By GEPRC

The GEPRC SPEEDX2 2306E Motor is a 1860 KV propulsion component for 4–5-inch FPV quadcopters. It combines CNC-machined 7075 aluminum construction, cooling cutouts and propeller-retaining protrusions. Its integration requirements include a 16*16mm mounting pattern, 6S input and a specified 40A/6S compatible ESC.

T-MOTOR VL1165 KV60 motor with packaging box and mounting hardware.
Motors & ESCs

T-MOTOR VL1165 KV60 motor

By T-MOTOR

The T-MOTOR VL1165 KV60 is a 24S LiPo UAV propulsion motor with centrifugal cooling, IPX5 protection and a specified maximum thrust of 66 kg. Its integration requirements include a Φ120.5 × 67.9 mm motor envelope and 1710 g cable-inclusive mass. Reference performance covers the motor paired with a VL200A 24S ESC and VZ42 ×16.5-inch propeller.