ChinaDroneRequest a quote →

GLED CR401

The GLED CR401 from ShenZhen GLED Electronic Co., Ltd is a compact centimeter-level RTK GNSS receiver for model aircraft, flight controllers and small intelligent systems. Its 35 × 35 mm design integrates multifrequency satellite positioning, 4G connectivity, an eSIM data card, a six-axis MEMS IMU and a three-axis magnetometer.

GLEDDrone flight controller
Dimensions
35 × 35 mm.

Get a free quote

Product overview

The GLED CR401 from ShenZhen GLED Electronic Co., Ltd combines a Sinan multimode, multifrequency RTK module, onboard 4G connectivity and an integrated eSIM data card in a 35 × 35 mm receiver. Designed for model aircraft, flight controllers and small intelligent systems, it supports GPS, GLONASS, BDS, Galileo, QZSS and SBAS signals. RTK positioning accuracy is ±(8 mm + 1 ppm) horizontally and ±(15 mm + 1 ppm) vertically, expressed as RMS. Positioning updates are configurable up to 10 Hz.

A QMI8658A six-axis MEMS IMU and QMC5883P three-axis magnetometer provide inertial and magnetic sensing. FreeRTOS runs on the ML307R-DC hardware platform, with configuration available through USB or a WeChat mini program. The receiver provides a six-pin flight-controller connector, a separate two-pin power connector and dedicated MMCX connections for GNSS and 4G antennas. It accepts 5–18 V through either power connector and operates from −20°C to +75°C. One receiver unit is supplied. The receiver withstands a 1.5 m drop at room temperature and is not waterproof.

Flight control & navigation

Specifications

GLED CR401 specifications
SpecificationValue & conditions
Product type and applicationsCR401 miniature centimeter-level RTK GNSS receiver for model aircraft, flight controllers and small intelligent systems.
Integrated positioning and cellular equipmentOnboard 4G connectivity, integrated eSIM data card and Sinan high-precision multimode, multifrequency RTK module.
Dimensions35 × 35 mm.
Hardware and software platformsML307R-DC hardware platform; FreeRTOS software platform.
Configuration methodsOne-touch configuration through USB or a WeChat mini program.
LTE modes and frequency bandsLTE-FDD: Bands 1/3/5/8; LTE-TDD: Bands 34/38/39/40/41.
Cellular antenna, operators and transmit powerExternal 4G antenna connection; China Mobile, China Unicom and China Telecom support; transmit power 23 dBm ±2 dB.
Network protocolsIPv4, IPv6, PING, NTP, DNS, TCP, UDP, HTTP, HTTPS, MQTT, MQTTS and FTP.
Telemetry and custom protocolsMQTT telemetry and custom protocols including JT808.
GNSS signalsGPS L1/L5; GLONASS G1; BDS B1I/B2a; Galileo E1/E5a; QZSS L1C/A/L5; SBAS L1C/A.
GNSS data and correction formatsNMEA-0183 positioning data; RTCM3.X correction input/output.
GNSS update and acquisitionMaximum update rate 10 Hz; reacquisition less than 1 s; cold start less than 24 s.Configurable data update rate.
Single-point positioning accuracyHorizontal 1.5 m; vertical 3.0 m.Single-point positioning; RMS.
DGPS accuracyHorizontal 0.4 m; vertical 0.8 m.DGPS positioning; RMS.
RTK accuracyHorizontal ±(8 mm + 1 ppm); vertical ±(15 mm + 1 ppm).RTK positioning; RMS.
Timing and velocity accuracyTiming accuracy 20 ns; velocity accuracy 0.02 m/s.RMS.
Magnetometer model, range and resolutionQMC5883P three-axis magnetometer; measurement range ±30 Gauss (approximately ±3 mT); resolution 2 mG (0.2 µT).
Heading accuracy1°–2°.With a soft-iron/hard-iron magnetic calibration library.
Magnetometer data ratesMaximum 1.5 kHz; normal-mode settings 10/50/100/200 Hz.1.5 kHz in continuous mode; selectable rates in normal mode.
IMU constructionQMI8658A six-axis MEMS IMU.
Gyroscope specificationsRanges ±32/±64/±128/±256/±512/±1024/±2048 °/s; typical sensitivity error ±3%; bandwidth programmable to above 400 Hz.Seven selectable gyroscope ranges; sensitivity error is typical.
Accelerometer specificationsRanges ±2/±4/±8/±16 g; noise density 150 µg/√Hz.Four selectable accelerometer ranges.
Status indicatorsRed LED indicates normal power. Blue LED: slow flashing indicates LTE registration; fast flashing indicates network search/registration; off indicates module shutdown or sleep.
USB interfaceUSB Type-C interface at 115200 baud for parameter configuration/readout and log output.Connected to a computer serial port.
Six-pin connector1.25 × 6P connector: pin 1 GND; pin 2 IMU SDA; pin 3 IMU SCL; pin 4 GNSS TX; pin 5 GNSS RX; pin 6 VIN, 5–18 V. IMU IIC connection serves the three-axis accelerometer, three-axis gyroscope and three-axis magnetometer. GNSS serial interface uses TTL levels and NMEA-0183 positioning sentences, with default baud rate 115200.
Two-pin power connector1.25 × 2P power connector; input voltage 5–18 V.Use either power input; the two-pin connector may remain unpowered when power is supplied through the six-pin connector.
Two-pin connector groundPin 2: GND, power ground.
Antenna connectorsSeparate right-angle MMCX female connectors for GNSS positioning and 4G communications antennas.
Temperature and environmental limitsOperating temperature −20°C to +75°C; storage temperature −20°C to +85°C; withstands a 1.5 m drop at room temperature; not waterproof.Drop resistance applies at room temperature.
Supplied quantityOne receiver unit.Included equipment.

Related guides