Product overview
The GEPRC GEP-STABLE PRO F7 DUAL BL32 35A combines flight control, a four-in-one BLheli_32 ESC and a 5.8GHz video transmitter in a compact electronics stack for FPV aircraft integration. Its F7 controller uses an STM32F722RET6 processor and two SPI-connected ICM20689 inertial sensors that operate simultaneously. Onboard blackbox storage supports flight-data analysis, while the AT7456E-based BetaFlight OSD provides the display function. The controller includes an LC filter and a 5V@3A BEC, but has no barometer. Both the controller and ESC accept 2–6S LiPo input.
Installation requires attention to each board’s footprint: the controller measures 26x26mm, the ESC extends to 31x31mm including power pads, and the VTX measures 24x26mm. The stated stack size is 26x26x21mm, with 20x20mm M2 mounting and soft silicone hardware. The complete configuration includes the three electronics modules, antenna, capacitor, cables and mounting pieces; it is an electronics assembly rather than a flight platform or airframe kit. The ESC is rated at 35A continuous and 45A for three seconds. The 5V VTX offers 48 channels and selectable output through 600mW, including a zero-output Pit mode.
Specifications
| Specification | Value & conditions |
|---|---|
| Listed product weight | 150 g |
| Configuration options | FC+ESC+VTX, F722 Flight Controller, 35A BLheli_32 ESC, 5.8G VTX |
| Flight controller model | STABLE PRO F7 35A |
| Flight controller MCU | STM32F722RET6 |
| Flight controller IMU | 2x ICM20689(SPI) |
| Blackbox storage | 32Mb onboard Flash |
| On-screen display | BetaFlight OSD w/ AT7456E chip |
| Flight controller BEC output | 5V@3A |
| Flight controller input voltage | 2-6S Lipo |
| Flight controller firmware target | EXF722DUAL |
| Flight controller board and mounting dimensions | 26x26mm board, 20mm mounting holes (M2) |
| ESC MCU | STM32F051 |
| ESC battery input | 2-6s lipo |
| ESC continuous current | 35Amps |
| ESC burst current | 45AmpsMaximum current for 3 seconds. |
| ESC dimensions | 31*31mm(including the power pads)Including the power pads. |
| ESC mounting holes | 20*20mm,M2 |
| ESC firmware target | GEPRC-BL32-4IN1 |
| VTX input voltage | 5V |
| VTX channel count | 48 |
| VTX transmission power settings | 0mW(Pit mode) / 25mW / 100mW / 200mW / 400mW/ 600mW0mW setting is Pit mode. |
| VTX dimensions | 24 * 26 mm |
| VTX mounting hole spacing | 20mm x 20mm |
| VTX BEC output | 5V/1A for Camera of FCFor Camera of FC. |
| VTX weight | 2.3g |
| Stack mounting holes | 20x20mm(M2) |
| Stack dimensions | 26x26x21mm |
| Stack weight with hardware | 16.5gIncluding wire and screws. |
| Included equipment | 1 F7 flight controller; 1 BLheli_32 35A 2-6S ESC; 1 5.8GHz 600mW VTX; 1 antenna; 1 capacitor; 5 cable sets; 4 M2*28mm screws; 16 soft silicone pieces.FC+ESC+VTX configuration. |
| Barometer | No |
Request a quote for GEP-STABLE PRO F7 DUAL BL32 35A
Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.
Submit your procurement requirements ↗No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.
