Carbon Fiber tube Φ25x350mm S1100 Replacement Arm (2pcs)
By RCTimerThe RCTimer Carbon Fiber tube Φ25x350mm S1100 Replacement Arm (2pcs) supplies two hollow replacement arm tubes for the S1100. Each tube is 350mm long, with a 25mm outer diameter and 23mm inner diameter, and uses 100% carbon fiber with a 3K twill weave.
Explore product ↗industryRctimer CF2812 1534KV Outrunner Brushless Motor
By RCTimerThe Rctimer CF2812 1534KV Outrunner Brushless Motor, designated CF2812-14, is a 50 g aircraft propulsion component. It has a 28.7 × 32 mm motor body, a 3.17 × 48 mm shaft, 206 W maximum power and a 20–30 A ESC specification.
Explore product ↗industryRctimer CF2822 1200KV Outrunner Brushless Motor
By RCTimerThe Rctimer CF2822 1200KV Outrunner Brushless Motor is a 50 g propulsion component designated CF2822-14. It combines a diameter 28.7 × 32 mm motor body with a diameter 3.17 × 48 mm shaft, a 200 W maximum power specification, and listed battery, propeller and ESC integration parameters.
Explore product ↗industryDD M3 RC Vibration Bobbins 10x10mm (10pcs/bag)
By RCTimerThe Rctimer DD M3 RC Vibration Bobbins are silicone-based vibration mounts for multirotor camera platforms and flight controllers. Identified as DD10M3, each bobbin measures 10mm in diameter by 10mm high, uses an M3 mounting size and weighs 1.48g. Each bag contains 10 pieces.
Explore product ↗industryRctimer Fixhawk/3DR Pixhawk 32bit Flight Controller
By RCTimerThe Rctimer Fixhawk/3DR Pixhawk 32bit Flight Controller is an autopilot module combining Cortex M4 processing, onboard motion and magnetic sensors, and a dedicated failsafe co-processor. It provides 14 PWM/servo outputs, peripheral interfaces and redundant power inputs. The supplied controller package includes a mounted memory card, safety switch, buzzer and connection cables.
Explore product ↗industryFixHawk/Pixhawk I2C Splitter
By RCTimerThe RCTimer FixHawk/Pixhawk I2C Splitter expands a controller’s I2C port through five four-position DF13 connectors, providing four additional peripheral ports. This compact accessory measures 32 mm x 12 mm x 6 mm and includes one splitter module and one cable.
Explore product ↗industryFTDI Tool V1.0
By RCTimerThe RCTimer FTDI Tool V1.0 is an FT232RL USB-to-serial breakout board with a bottom-mounted six-pin header and TX/RX LEDs. DTR enables automatic reset during sketch downloads when the Arduino target routes its reset pin to a six-pin connector. It ships at 5V; switching power output and IO to 3.3V requires cutting a trace and adding a solder jumper.
Explore product ↗industryRCTimer Gyro / Flight Controller Mounting Pad (10pcs)
By RCTimerThe RCTimer Gyro / Flight Controller Mounting Pad (10pcs) is a ten-piece adhesive mounting accessory for gyros, flybarless systems and flight controllers. Its soft yet sufficiently rigid material combines vibration damping with restraint of device movement, and the pads use 3M adhesive.
Explore product ↗industryRctimer HP1410 4000KV FPV Racing Brushless Motor
By RCTimerThe Rctimer HP1410 4000KV FPV Racing Brushless Motor is a 5g motor with a 9N12P configuration and 1.5mm shaft. It specifies 1-2S LiPo operation, with maximum continuous ratings of 9A and 63W each qualified by 180 seconds. Selectable KV values are 4000KV and 6500KV.
Explore product ↗industryRctimer HP2217 800KV 930KV 1200KV High Performance Brushless Motor
By RCTimerThe Rctimer HP2217 High Performance Brushless Motor is a multirotor propulsion component offered in 800KV, 930KV and 1200KV versions. It supports 2S~4S LiPo batteries and combines a dynamically balanced rotor, 0.20mm laminations, flexible silicone-covered leads and preinstalled 3.5mm bullet connectors.
Explore product ↗industryRctimer HP2814 710KV 810KV 980KV Multirotor Brushless Motor
By RCTimerThe Rctimer HP2814 multirotor brushless motor offers 710KV, 810KV and 980KV selections and specifies 2S~6S LiPo batteries. Weighing 100g (4oz), it features 0.20mm laminations, NSK or NMB bearings, rotor dynamic balancing and preinstalled 3.5mm bullet connectors.
Explore product ↗industryRctimer HP4108 480KV (24N22P) Multirotor Brushless Motor
By RCTimerThe Rctimer HP4108 is a multirotor brushless motor with a 480 KV rating and 24N22P configuration. This propulsion component has a specified motor wire length of 37cm for integration into a multirotor assembly.
Explore product ↗