ChinaDrone.Request a quote ↗
COMPONENT

Kpower HBL836 25kg All-Aluminium Metal Gear Brushless Standard Servo

By Kpower ↗

The Kpower HBL836 is an aluminum-alloy, metal-gear brushless servo for fixed-wing drones and robotic or automation assemblies. Its 40x20x39mm body weighs 72g and incorporates potentiometer feedback, dual output-shaft bearings and PWM control. Specified stall torque is 26kg·cm at 7.4 V, with 180° travel and IP42 protection.

ProductKpower HBL836 25kg All-Aluminium Metal Gear Brushless Standard Servo
ApplicationsDesktop robotic arm; fixed-wing drone; industrial automation; service robot
Stall torque26kg·cm7.4 V
No-load speed0.13sec/60°7.4 V
Travel angle180°Customization supported.
Voltage range4.8-7.4V

Product overview

The Kpower HBL836 25kg All-Aluminium Metal Gear Brushless Standard Servo is a positioning component for fixed-wing drones, desktop robotic arms, service robots and industrial automation. Its architecture combines a brushless motor, metal gearing and an aluminum-alloy case with a digital MCU drive system. A high-linearity potentiometer provides position feedback, while two ball bearings support the output shaft. The low-backlash gear mechanism and 25T, Φ5.9mm spline define key mechanical features for integration into a driven assembly.

The servo occupies 40x20x39mm and weighs 72g, providing concrete dimensions and mass for installation planning. Its electrical operating range is 4.8-7.4V; at 7.4 V, stall torque is 26kg·cm, no-load speed is 0.13sec/60°, and stall current is 4500 mA. The specified configuration uses PWM signaling and 180° travel, with customization supported for both. IP42 protection also carries a customization option. The operating temperature range is -10 to 50°C, setting an environmental limit for integration.

Specifications

SpecificationValue & conditions
ProductKpower HBL836 25kg All-Aluminium Metal Gear Brushless Standard Servo
ApplicationsDesktop robotic arm; fixed-wing drone; industrial automation; service robot
Stall torque26kg·cm7.4 V
No-load speed0.13sec/60°7.4 V
Travel angle180°Customization supported.
Voltage range4.8-7.4V
Dimensions40x20x39mm
Weight72g
Stall current4500 mA7.4 V
Case materialAluminum alloy
Gear materialMetal
Output spline25T Φ5.9mm
MotorBrushless
Bearings2BB
Position sensorPotentiometer
Signal and protocolPWMCustomization supported.
Ingress protectionIP42Customization supported.
Operating temperature-10~50°C
Gear mechanismLow-backlash mechanism with metal teeth
Position feedback componentImported high-linearity potentiometer
Output shaft supportDouble ball bearings on the output shaft
Drive electronicsIntelligent digital MCU drive system

Ask for the Kpower HBL836 25kg All-Aluminium Metal Gear Brushless Standard Servo price ↑

KEEP EXPLORING

Similar products

Browse all products ↗
GEPRC GEP-PTHD Frame with black plates and red antenna mounts
Propellers & airframes

GEP-PTHD Frame

By GEPRC

The GEPRC GEP-PTHD Frame is a compact airframe kit for a 2.5-inch UAV intended for maneuvering in narrow spaces. Its approximately 19.7g frame combines bottom, top and side plates with mounting provisions for motors, a flight controller and a small camera. Assembly hardware, antenna fittings, battery retention accessories and damping parts are included.

DJI S800 retractable landing gear assembly
Propellers & airframes

DJI S800

By DJI

The DJI S800 is retractable landing gear. Its defining function is the ability to retract and extend the landing gear, identifying the product as a landing hardware component within DJI’s S800 product identity.

FlashHobby CLS1227RP 11KG CLS Servo V2 with mounting bracket and servo horn
Propellers & airframes

CLS1227RP 11KG CLS Servo V2

By FlashHobby

The FlashHobby CLS1227RP 11KG CLS Servo V2 is a digital micro servo for the HORIZON SCX24 1/24-scale RC car. It combines a coreless motor, steel gearing and an aluminum case, with a 25-tooth output spline. Operation spans 6.0–8.4 V DC, reaching 11.0 kg-cm stall torque at 8.4 V.