| Product | Happymodel Moblite6 1S 65mm ultra light brushless whoop |
|---|
| Wheelbase and size | Wheelbase: 65mm; size: 80mm*80mm*25mm |
|---|
| Weight | 18.5gWithout battery. |
|---|
| Weight with battery | 26gWith original 1s 300mah LiPo battery. |
|---|
| Construction | 1S AIO 5IN1 F4 flight controller; Unibell EX0802 brushless motors; low-profile canopy |
|---|
| Frame | 1 × 65mm frame (Mobula6 frame)Included equipment. |
|---|
| Flight controller options | DiamondF4 FR with built-in SPI Frsky receiver, or DiamondF4 FS with built-in SPI Flysky receiverSelected receiver version. |
|---|
| Motors | 4 × EX0802 KV19000 Unibell brushless motorsIncluded equipment. |
|---|
| Propellers | 1 set of Gemfan 1219 31mm propellers (4cw+4ccw)Included equipment. |
|---|
| Camera | 1 × Runcam Nano3Included equipment. |
|---|
| Included video transmitter | 1 × built-in 5.8G 40ch 25mw-200mw VTXStandard built-in VTX configuration. |
|---|
| Batteries | 2 × 1s 300mah LiPo batteriesIncluded equipment. |
|---|
| Charger | 1 × 1S USB chargerIncluded equipment. |
|---|
| Propeller removal tool | 1 × propeller removal toolIncluded equipment. |
|---|
| Screwdriver | 1 × screwdriverIncluded equipment. |
|---|
| Carry case | 1 × Happymodel carry caseIncluded equipment. |
|---|
| Motor specifications | EX0802 19000KV; 9N12P; stator diameter: 8mm; stator length: 2mm; shaft diameter: Φ1mm; motor dimensions (diameter × length): Φ10.5mm*14.9mm; weight: 1.7g; LiPo: 1S onlyMotor battery requirement: 1S LiPo only. |
|---|
| Flight controller specifications | Firmware targets: CrazybeeF4FR / CrazybeeF4FS respectively; STM32F411CEU6 MCU (100MHZ, 512K FLASH); MPU-6000 sensor with SPI connection; original whoop size compatible; built-in 5A(each) Blheli_S 4in1 ESC, Dshot600 ready; Betaflight OSD with SPI control; built-in 5.8G VTX, SPI Frsky/Flysky receiver and 5V 1A BECFrsky SPI RX version: DiamondF4 FR; Flysky SPI RX version: DiamondF4 FS. Power input: 1S battery, DC 2.9V-4.35V. |
|---|
| Onboard 4in1 ESC | EFM8BB21 MCU; 5A continuous, 6A peak (3 seconds); BLHeliSuite programmable; factory firmware: O_H_5_REV16_8.HEX; default protocol: DSHOT6001S LiPo/LiPo HV supply; peak current duration: 3 seconds. |
|---|
| Frsky receiver | SPI BUS receiver; Frsky D8 compatible; compatible with Non EU transmitter D8 mode; 8ch; failsafe support; range: 200m~300mFrsky SPI D8 receiver version; range with no ground interference and transmitter and receiver 1 m from the ground. |
|---|
| Flysky receiver | SPI BUS receiver; switchable AFHDS and AFHDS-2A; 8ch (AFHDS) or 14ch (AFHDS-2A); range: 200~300m; failsafe supportFlysky SPI receiver version; range with no ground interference and transmitter and receiver 1 m from the ground. |
|---|
| Video transmitter specifications | Output power: 25mw~200mw switchable; frequency: 5.8GHz; 5 bands, 40 channels including Race band; current consumption: 300mA typical; Smartaudio readyStandard onboard 5.8g VTX configuration. |
|---|
| OPENVTX maximum output | Maximum output: 400mwMoblite6 Frsky version equipped with DiamondF4FR V3.2 and built-in OPENVTX. |
|---|
| RunCam Nano 3 specifications | 1/3″ CMOS sensor; 800TVL; 2.3mm(M6.5) lens; FOV: 140°; PAL/NTSC non-switchable; S/N ratio: greater than 50dB; automatic electronic shutter, AGC and D-WDR; minimum illumination: 0.01Lux@1.2F; color day/night; power: DC 3-5.5V; current: 110mA@5V, 120mA@3.3V; ABS housing; net weight: 1.2g; dimensions: L14mm*W14mm*H9mm |
|---|
| LiPo battery specifications | - Capacity: 300mAh;
- voltage: 3.8v;
- continuous discharge rate: 30C;
- size: 57mmx12mmx7mm;
- weight: 7.5g;
- connector: PH2.0
|
|---|