Product overview
The GEPRC MOZ7 V2 O4 Pro is a long-range FPV flight platform supplied with propulsion, flight electronics and a DJI O4 Air Unit Pro camera and video transmitter. Its imaging system combines a 1/1.3-inch sensor with a 155° field of view, 1080p/100fps H.265 transmission and recording up to 4K/120fps. It also supports 10-bit D-Log M and a transmission distance extending to 15 km. Receiver choices are PNP, ELRS 915MHz/2.4G GemX and TBS Nano RX; the ELRS configuration uses front-horizontal and rear-vertical antenna positioning.
The GEP-MOZ7 V2 frame has a 336mm wheelbase, 6mm arms, 2.5mm top and base plates, and a 3mm middle plate. Reinforced side bars support a balanced center of gravity, while a 7075 aluminum protector surrounds the camera and the FPV view excludes the propellers. Integration flexibility comes from a swappable action camera mount and two battery mounting options. The HD version weighs 750±10g. Flight electronics include a TAKER H743 BT controller with STM32H743 MCU, dual gyroscopes, a barometer, GEP-M1025 GPS and BetaFlight OSD.
The propulsion configuration uses SPEEDX2 2809 1280KV V1.1 motors, a TAKER H65_8S_32Bit 65A four-in-one ESC and HQ 7.5*3.7*3 three-blade propellers. Power connects through an XT60E-M, with LiPo 6S 3300mAh or Li-ion 8000mAh batteries recommended. The 25-minute flight-time figure applies to slow cruising; product differences, firmware, flying style and environment can change endurance. Supplied accessories include propellers, two battery straps, two anti-slip pads, three sizes of L-shaped screwdriver, spare screws, a pairing pin, two VTX antennas and a tri-band stick antenna.
Specifications
| Specification | Value & conditions |
|---|---|
| Model and purpose | GEPRC MOZ7 V2 O4 Pro long-range FPV drone |
| Frame | GEP-MOZ7 V2 |
| Wheelbase | 336mm |
| Top plate thickness | 2.5mm |
| Base plate thickness | 2.5mm |
| Middle plate thickness | 3mm |
| Arm thickness | 6mm |
| Flight controller | TAKER H743 BT |
| MCU | STM32H743 |
| Gyroscopes | MPU6000 and 42688-P dual gyroscopes |
| Barometer | Yes |
| GPS | GEP-M1025 |
| OSD | BetaFlight OSD with AT7456E chip |
| ESC | TAKER H65_8S_32Bit 65A 4IN1 ESC |
| Video transmitter | DJI O4 Air Unit Pro Air Unit module |
| Camera | DJI O4 Air Unit Pro camera module |
| Antenna | Momoda2-5.8G-SMA-LHCP-170mm |
| Power connector | XT60E-M |
| Motor | SPEEDX2 2809 1280KV V1.1 |
| Propeller | HQ 7.5*3.7*3 three-blade, transparent grey |
| Version weight | 750±10gHD version. |
| Receiver options | PNP, ELRS 915MHz/2.4G GemX, TBS Nano RX |
| Recommended battery | LiPo 6S 3300mAh / Li-ion 8000mAh |
| Flight time | 25 minsTested at slow cruising speeds; actual flight time may vary with product differences, firmware version, flying style and environment. |
| Camera protection and framing | Reinforced frame, more centered center of gravity and 7075 aerospace aluminum camera protector; propellers outside the FPV view |
| Camera and battery mounting | Swappable action camera mount and two battery mounting options |
| Imaging and video link | 1/1.3-inch sensor; 155° field of view; 1080p/100fps H.265 transmission; recording up to 4K/120fps; transmission distance to 15 km; 10-bit D-Log MDJI O4 Air Unit Pro. |
| Receiver antenna arrangement | Front-horizontal and rear-vertical arrangementELRS 915M/2.4G Gemx dual-band receiver configuration. |
| Supplied configuration | 1 × GEPRC MOZ7 V2 FPV; 2 × HQ 7.5*3.7*3 (2CW+2CCW); 2 × 15*250mm battery straps; one each 1.5mm, 2.0mm and 3.0mm L-shaped screwdriver; 1 × spare screw pack; 2 × battery anti-slip pads; 1 × frequency pairing ejector pin; 2 × VTX antennas; 1 × tri-band stick antenna |
Request a quote for GEPRC MOZ7 V2 O4 Pro
Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.
Submit your procurement requirements ↗No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.