Product overview
The GEPRC Cinelog30 V3 O4 Pro Quadcopter is a flight platform for cinematic aerial footage, combining an O4 camera and O4 Air Unit Pro video transmitter with a Cinelog series underslung gimbal mount. Its GEP-CL30 V3 frame uses 2.5mm carbon fiber plates and a 128mm wheelbase. Aluminum reinforcement strengthens the frame, while a wrap-around electronics compartment protects internal components. A canopy shields the camera against impacts, and dust-proof plugs protect the data ports from debris during takeoff and landing.
The electronics layout centers on a TAKER F722 45A 32Bit AIO flight system and a rear power distribution board for organized wiring. The custom PDB includes receiver, buzzer, LED BEC, TVS and anti-spark features. SPEEDX2 1404 3850KV motors drive HQprop DT76mmx3 V2 propellers, with an XT30 battery connector. Receiver configurations comprise PNP with a digital built-in VTS receiver, ELRS 2.4G and TBS NanoRX. Weight is 187±2g for the TBS NanoRX version, and recommended batteries are LiHV 4S 660mAh-720mAh.
The package supplies the quadcopter, a transparent-black protective frame, two pairs of propellers, grey and black canopies, a 15*150mm battery strap and an anti-slip pad. Service accessories include a 1.5mm L-shaped screwdriver, spare screws and damping balls, a damping ball puncher and a frequency pairing ejector pin. With a LiHV 4S 720mAh battery, flight time reaches up to 8 minutes 10 seconds at slow cruising speeds; actual duration varies with flying method. This endurance figure therefore carries a specific battery and flight-speed condition.
Specifications
| Specification | Value & conditions |
|---|---|
| Model | GEPRC Cinelog30 V3 O4 Pro Quadcopter |
| Configuration options | PNP, ELRS 2.4G, TBS Nano RX |
| Frame model | GEP-CL30 V3 |
| Carbon fiber plate thickness | 2.5mm |
| Wheelbase | 128mm |
| Flight system | TAKER F722 45A 32Bit AIO |
| MCU | STM32F722RET6 |
| Gyro | ICM 42688-P |
| Flight controller firmware | GEPRC_F722_AIO |
| Flash | 16MB |
| ESC | 32Bit 45A |
| Motor | SPEEDX2 1404 3850KV |
| Propeller | HQprop DT76mmx3 V2 |
| Battery connector | XT30 |
| Video transmitter | O4 AIR Unit Pro |
| Camera | O4 |
| Antenna | O4 original |
| Receiver | PNP(digital built-in VTS receiver) / ELRS2.4G / TBS NanoRX |
| Weight | 187±2gTBS NanoRX version. |
| Recommended battery | LiHV 4S 660mAh-720mAh |
| Flight time | 8’10″Tested at slow cruising speeds; actual times may vary with flying method. |
| Protective architecture | Aluminum-reinforced frame, wrap-around electronics compartment, dust-proof data-port plugs and camera-protecting canopy. |
| Power distribution layout | Rear power distribution board for organized wiring and component layout. |
| Power distribution board features | Custom PDB with receiver, buzzer, LED BEC, TVS and anti-spark features. |
| Camera mounting | Cinelog series underslung gimbal mount.O4 Air Unit PRO installation. |
| Supplied configuration | Flight platform with 1 Cinelog30 V3, 1 transparent-black protective frame, 2 pairs of HQprop DT76mmx3 V2 propellers, 1 15*150mm battery strap, 1 1.5mm L-shaped screwdriver, 1 grey canopy, 1 black canopy, 1 spare screw pack, 1 battery anti-slip pad, 1 damping ball puncher and 1 frequency pairing ejector pin. |
| Spare pack contents | 1 M2 rivet nut; 4 M2*4.5, 4 M2*6 and 4 M2*4 button-head hex socket screws; 1 M2*12 button-head screw; 2 damping balls.Included spare screw pack. |
Request a quote for GEPRC Cinelog30 V3 O4 Pro Quadcopter
Send your application, destination country and expected quantity to the ChinaDrone team. We can discuss product selection, configuration and sourcing from China.
Submit your procurement requirements ↗No account needed. A model number is optional. Your enquiry is handled by ChinaDrone.