T-Motor F60 Pro V vs EMAX ECO II 2306 Procurement Guide
Compare winding choices, battery compatibility, installed weight and service parts for five-inch racing, club and freestyle builds.
A club replacing one damaged motor should start with the marking on the other three. A team choosing motors for a new fleet has more room to choose. The standard T-Motor F60 Pro V offers four windings on a 2207.5 stator, including a 2550KV option explicitly specified for 4S racing. The EMAX ECO II 2306 offers three windings, with published battery ranges for each and a dimensioned drawing that helps a workshop check fit before ordering. Make the first cut using the packs and propellers the pilots already use. Then compare the exact windings that remain eligible.
Compare the standard motors
| Part | What to look for | Matching products |
|---|---|---|
| Stator and winding | F60 Pro V uses a 2207.5 stator with 1750, 1950, 2020 or 2550KV. ECO II uses a 2306 stator with 1700, 1900 or 2400KV. | |
| Battery choice | T-Motor lists 1950KV at 6S, 2020KV at 5–6S and 2550KV at 4S. Confirm the 1750KV rating. EMAX lists 1700/1900KV at 3–6S and 2400KV at 3–4S. | |
| Mass basis | T-Motor lists 34.3, 33.9, 33.8 and 33.3 g in ascending KV order with leads. EMAX lists 30.4, 30.2 and 30.2 g respectively without leads. | |
| Envelope and wiring | T-Motor lists 26.8 mm diameter by 31.7 mm and 150 mm leads. EMAX specifies 28 mm by 31.6 mm and 120 mm leads. Both use 20 AWG leads. | |
| Prop and mounting hardware | T-Motor recommends five-inch props and lists a 5 mm prop mount. EMAX specifies 5–5.5 inches, an M5 nut and a 16 × 16 mm mounting pattern. |
Send this list as it is and get one price for every part.
Quote the full parts list →KV describes a motor's approximate unloaded speed per volt. It is useful when identifying a winding, but the speed under load also depends on the propeller and battery. Two close KV labels do not establish that two builds will draw the same current or feel alike to the pilot. On the order, write the family, generation and winding together. For a repair, include a photo of the existing bell and its original packaging if available. A carton marked only with the stator size leaves the person picking the replacement to guess which winding is inside.
Choose around the club's battery stock
For a team committed to four-cell packs and a five-inch race frame, the F60 Pro V 2550KV and ECO II 2400KV are two documented candidates. Ask the pilots what they need from the replacement. A team that shares identical race quads may value consistent control feel after a repair. A club building first freestyle quads may care more about whether the same spares fit each frame and whether members can keep using their chargers and props. Give each test pilot the same frame and pack specification so feedback refers to the motor choice.
For six-cell packs, the standard F60 Pro V 1950KV and 2020KV have explicit manufacturer ratings that include 6S. On the EMAX side, both the 1700KV and 1900KV sheets cover 3S through 6S. The standard T-Motor 1750KV listing contains inconsistent voltage information. Request the current data sheet for that winding before assigning it to a pack. T-Motor also sells a V-LV version in 1950KV and 2020KV. Keep that suffix on any offer that includes it, particularly when a supplier is filling a short order from more than one batch.
Read the bench sheet by propeller
The EMAX 1700KV test sheet illustrates how easily a peak figure can mislead. At 25.2 V the manufacturer records 1,500 g of static thrust and 23.5 A with a DALPROP Cyclone 5040 at maximum. With a Cyclone 5050 on the same sheet, the maximum row reads 1,710 g and 34.8 A. An extra 210 g on that stand came with an extra 11.3 A. For a buyer who already stocks the 5040, the first row is the relevant one. Taking the thrust from one row and the current from the other would understate the electrical load.
When comparing brands, ask for the propeller model, supply voltage, current and duration behind each number. T-Motor describes the 49.3 A peak for the standard 1950KV motor as a ten-second figure. A brief peak gives the purchaser a reason to examine the electronic speed controller's ratings and cooling in the intended build. It supplies little evidence about continuous operation. Have the builder review the proposed motor, propeller, battery and speed controller together. If a matching test is missing, leave that comparison open and evaluate a sample before approving a fleet substitution.
Need a quote for this? Tell us what you need →
Choose a second point on the bench sheet that represents ordinary practice flying. On the EMAX chart, both Cyclone propellers have a row at 700 g. The 5040 draws 8.5 A there and the 5050 draws 9.4 A. That comparison answers a different purchasing question from the maximum rows. A club interested in how its existing batteries will fare over a session can start with the load pilots use frequently, then review peak demand separately with the builder.
Check what will actually fit
The stator numbers describe internal geometry. The drawings and external dimensions tell the workshop how much room the motor occupies on the arm. Pay particular attention to the space between the rotating bell and any arm guard. For EMAX, check the published hole pattern against the frame drawing and select the mounting screw length for the arm and guard together. A screw that works with a thick guard can reach the winding after the guard is removed. Verify clearance on the sample with the battery disconnected before issuing hardware bags to the rest of the club.
The propeller attachment and the internal bearing shaft are two different dimensions on a parts list. For example, EMAX shows a 4 mm bearing shaft and an M5 propeller thread. Someone sourcing a prop nut from the shaft figure would order the wrong part. Ask for the propeller hub, nut and mounting hardware as separate lines if workshops keep their own spares. For T-Motor, request the replacement bell or shaft assembly against the full version name. A common prop mounting size provides no evidence that a bell will fit the other manufacturer's base.
Lead length can settle an otherwise close choice. Trace the route from the motor to the speed controller on a spare arm, including the bend around the guard. T-Motor supplies 150 mm leads and EMAX specifies 120 mm. Measure before trimming the first sample. For a weight comparison, weigh each candidate with the lead length the frame actually uses, the prop nut and the mounting hardware. Save that figure with the build sheet. T-Motor's published weights include cable, whereas EMAX's drawing explicitly excludes silicone wire. Subtracting the catalog figures would give a spurious weight saving.
Order and receive a repairable fleet
Count complete sets for the new builds, then count loose replacements for each winding separately. Ask whether a line on the offer represents one motor or a set and whether each unit includes a locknut and screws. On receipt, keep the outer label with the motor until its markings have been recorded. Label loose stock so a mechanic searching for an ECO II 1900KV can distinguish it from a different ECO generation or a nearby winding at a glance. Keep a sample of the approved hardware beside the workshop's frame drawing.
For purchases across regions, request the exact part identifier, destination service contact and contents of the locally supplied package. If the order covers motors alone, the shipper needs a packing list that reflects that. If LiPo packs are added, give the carrier their model, labelled watt-hours, quantity and packing arrangement and obtain route-specific acceptance and packing instructions. Keep the battery decision separate on the order so a change to the pack shipment does not silently change the approved motor winding.
For the sample evaluation, have the technician record the installed weight, wire reach and propeller clearance. Have the pilot record the prop model, pack and observations after the same practice session used for the club's existing build. Tag the approved combination on the order and retain the spare motor in its labelled bag. Contact our team with the frame drawing, cell count, propeller, speed controller, destination and required quantities by KV for an itemized inquiry.
Frequently asked questions
Which options suit an existing 4S race fleet?
Shortlist the F60 Pro V 2550KV and ECO II 2400KV, then check the exact propeller and controller pairing.
Is the T-Motor V-LV the same order line?
T-Motor lists V-LV separately. Specify standard V or V-LV even where the KV markings coincide.
Which motor is lighter on the frame?
Weigh both with the same installed lead length and hardware. The published figures use different weighing conditions.
Can a loose 1900KV ECO II replace a different winding?
For a single-motor repair, match the installed family and winding. Evaluate a winding change as a complete build change.
What makes a thrust comparison reproducible?
Request the exact prop, voltage, duration, thrust and measured current for each motor at the same test point.