Holybro Pixhawk 6X vs CUAV X7+ Pro | Flight Controller Procurement Guide
Compare Pixhawk 6X Rev 8 and X7+ Pro sensors, carrier boards, power monitoring and revision support for survey and agricultural equipment.
For a new survey aircraft, start with the wiring drawing. Holybro's Pixhawk 6X is a candidate when the design calls for a modular Pixhawk controller and a carrier with Ethernet. CUAV's X7+ Pro merits a closer look when the equipment specification names the ADIS16470 inertial sensor or the aircraft already uses CUAV power monitoring. The processor speeds are similar enough that neither number settles the purchase. A more revealing question is whether a technician can replace the controller and restore all the approved instruments using the spares in the service case.
Compare the controller assemblies
| Part | What to look for | Matching products |
|---|---|---|
| Main processor | Holybro lists STM32H753 in its technical guide and H753/H743 on its product page. CUAV specifies STM32H743. Both publish up to 480 MHz. | |
| Inertial sensors | 6X Rev 8 uses three ICM-45686 units. X7+ Pro combines ADIS16470, ICM-42688-P and an ICM-20689-family unit. | |
| Pressure and compass | Holybro documents ICP20100 plus a member of the BMP388/580/581 group and a BMM150 compass. CUAV lists two MS5611 barometers and an RM3100 compass. | |
| Actuator outputs | Holybro lists 16 PWM outputs. CUAV lists 14, including 12 with DShot support. | |
| Wired interfaces | Holybro lists 100 Mbps Ethernet. Its Standard v2 has two CAN connectors, while the Mini pinout shows one. CUAV lists two CAN ports and six I2C connections including two on shared connectors. Its port list omits Ethernet. | |
| Controller supply | Holybro lists a 6 V maximum. CUAV specifies 4.5 to 5.4 V. Both list 4.75 to 5.25 V for USB input. | |
| Mechanical scope | Holybro lists module and baseboard dimensions separately. CUAV gives 103 g for the controller in its English reference. | |
| Published temperature range | Holybro specifies -25 to 85 °C in its current technical and product pages. CUAV specifies -20 to 85 °C. | |
| Baseboard design | Pixhawk 6X uses the Pixhawk Autopilot Bus and has Standard v2A, Standard v2B and Mini bundle options. X7+ Pro uses a CUAV X7-family carrier. Compare order-specific port drawings. | |
| Power monitoring | Holybro offers PM02D digital monitoring. CUAV uses analog monitoring on Power A and a DroneCAN power monitor on Power C. Confirm the included meter and harness. | |
| Firmware | Holybro lists PX4 and ArduPilot for Rev 8 and ships it with PX4. CUAV lists PX4 and ArduPilot for X7+ Pro. Validate the exact version and board target. | |
| Product revisions | Holybro lists standard Rev 8 as the replacement for its older 6X listing. CUAV identifies X7+ Pro as the replacement for X7 Pro from January 1, 2022. |
Send this list as it is and get one price for every part.
Quote the full parts list →The Holybro column refers to the standard Pixhawk 6X Rev 8. Pixhawk 6X Pro is a separate product. Holybro also offers its controller module on its own and with different baseboards. State which assembly a purchasing line covers before comparing dimensions, weight or port access. CUAV likewise distinguishes X7+ Pro from X7+, X7 and X7 Pro. A missing plus sign can deliver a board with different inertial sensors even when the family name on the paperwork looks familiar.
Select for the instruments the aircraft carries
For an environmental survey platform with an onboard computer, identify what information the computer exchanges with the flight controller. If the design requires Ethernet, Holybro documents a 100 Mbps transformerless interface. Obtain the drawing for the chosen baseboard and have the integrator identify the matching connection on the computer side. The number in the specification describes the physical interface. A data logger that needs a particular message format and update rate still needs an acceptance test with the selected software.
For agricultural field mapping, a service fleet may already hold CUAV carriers, power modules and navigation receivers. Inventory those parts by model and revision before giving existing stock a value in the comparison. Give particular attention to the second positioning receiver. CUAV identifies UART4 as a possible second GPS connection and places some I2C connections within shared connectors. Count the plugs the technician can actually use together after the first receiver, telemetry equipment and field instruments have been assigned.
A laboratory studying sensor behavior may have a different reason to specify one model. The standard Holybro Rev 8 uses three ICM-45686 inertial units. CUAV combines an ADIS16470 with two other inertial sensor types. If the research protocol requires one of these devices, make its identity a receiving criterion and keep a diagnostic report from the reference unit. For an operational survey crew, judge the complete installation by its recorded performance under the conditions in which the resulting maps will be delivered.
Three inertial units describe one aspect of redundancy. They do little to explain a lost survey log, a loose power connection or magnetic interference from equipment mounted nearby. Ask the integrator to supply a sample log from the intended installation and to show which sensor identities, warnings and power measurements the maintenance team can review. An engineer should be able to trace an unusual reading back to the installed hardware revision before authorizing a replacement.
Specify the carrier, power modules and cables
For Holybro, choose the carrier before freezing the enclosure drawing. Holybro publishes two heights for the module, 14.6 mm in the technical guide and 16.8 mm on the product listing. Use the drawing for the part being supplied when the enclosure clearance is tight. The base adds its own footprint and determines the direction in which cables leave the assembly. Holybro lists Standard v2A, Standard v2B and Mini options. Ask for the outline and connector map associated with the ordered part number. Leave enough access to read labels and remove each service cable without removing an unrelated instrument from the enclosure.
Need a quote for this? Tell us what you need →
CUAV lists a controller weight of 103 g in its English documentation. A comparison with Holybro's bare module would understate the mass of the Holybro installation. Put the equipped assemblies on the same scale with their mounting hardware, power leads and any extra interface boards. Use this figure when reviewing the aircraft mass budget. Keep component weights on the bill of materials as well, so a later change of baseboard can be evaluated without weighing every cable again.
Separate the aircraft battery voltage, the regulated controller supply and the actuator rail on the electrical drawing. CUAV gives 4.5 to 5.4 V for the Power A and Power C inputs in its English reference. Its servo rail accepts up to 10 V and is separate from board power. Holybro gives 6 V as the maximum controller input and lists a separate servo rail specification. These figures belong at different points in the power system. Have the supplier identify the power module that takes the aircraft's actual battery input.
CUAV's Power A uses analog measurement and Power C accepts a CAN battery monitor. Holybro documents two SMBus power inputs on the Standard v2 and one on the Mini. It offers bundles with the PM02D module. For either system, list the monitor, cable and connector as individual order items or identify the bundle that contains them. At acceptance, ask the technician to compare the voltage displayed in the ground software with a reference measurement and to identify which readings appear in the saved equipment log.
Plan firmware acceptance and future replacements
Record the ground software, autopilot firmware release and vehicle configuration already approved by the engineering team. Holybro documents PX4 preinstallation, and CUAV identifies both PX4 and ArduPilot support. Ask for the intended board target and evidence for the combination you will accept. In particular, verify the navigation receiver, power monitor, telemetry and log retrieval with the actual carrier. Support for a firmware family leaves several practical questions open when the installation includes instruments with their own drivers.
Holybro marks the Rev 3 and Rev 4 product listing discontinued and points buyers to Rev 8. Treat Rev 8 as a hardware change when maintaining an older fleet. CUAV states that X7+ Pro replaced X7 Pro from January 1, 2022. Its current documentation index lists X7+ Pro separately from the discontinued X7+. If a repair request names the older product, capture its exact marking and sensors before approving a substitute. That information helps the maintenance engineer decide which previous calibration records and acceptance results still apply to the repaired aircraft.
For a production order, retain a reference kit and an archive containing its connector drawings, parts list, software versions and sample logs. Have a technician other than the original integrator identify the controller and carrier, locate every accessory in the documentation and retrieve the acceptance log. Note any component that can only be identified by wire color or by remembering a verbal instruction. Give it a part number or an unambiguous description before releasing the remaining kits to the assembly bench.
For a long-running survey program, include revision notification in the purchase request. Specify who can approve a replacement sensor set and which documents that person needs. A shipment carrying the same family name may still require a new reference log. If the supplier proposes a different carrier, check access to the memory card and service connections with the enclosure closed before accepting the dimensional drawing.
For an inquiry, send our team the aircraft type, preferred firmware release, controller and carrier revisions in service, required sensor models and connection list. Include the intended power monitor and identify any parts you plan to reuse. A request that names only a Pixhawk-compatible controller leaves the two largest purchasing variables unresolved: which connections the delivered assembly exposes and which hardware change the operator is equipped to qualify.
Frequently asked questions
Which model matches a specification calling for an ADIS16470?
CUAV lists that device in X7+ Pro. Holybro lists three ICM-45686 units for the standard Rev 8.
Are all six CUAV I2C connections separate sockets?
CUAV documents four independent interfaces and two integrated with the GPS and UART4 connections. Review simultaneous use on the harness drawing.
Does the CUAV servo rail power the controller?
No. CUAV documents independent controller power through Power A, Power C or USB.
Can we order a 6X module as a complete spare?
A module-only order suits a repair where a verified carrier will remain in service. A complete spare assembly also needs the selected baseboard and associated hardware.
What replaced the original X7 Pro?
CUAV identifies X7+ Pro as its replacement from January 1, 2022. Capture the old board identity when planning a fleet repair.