DJI Zenmuse H20T vs DJI Zenmuse H30T: Procurement Guide
Compare thermal detail, temperature modes, visible cameras and Matrice compatibility when buying or replacing a DJI inspection payload.
Keep a serviceable Zenmuse H20T on the shortlist when it already produces the images your maintenance engineers need from a Matrice 300 RTK or 350 RTK. Give the newer H30T priority when a report routinely leaves a small component unresolved, when the work includes unusually hot equipment, or when the payload must move to a Matrice 400. Both are detachable camera payloads. The purchase decision therefore starts with the host aircraft and ends with the inspection file that someone must be able to interpret.
Compare the payloads on the purchase order
| Part | What to look for | Matching products |
|---|---|---|
| Thermal files | H20T records 640 × 512 at 30 Hz. H30T records native 1280 × 1024 at 30 fps. Both save R-JPEG stills. | |
| Visible cameras | H20T has 12 MP wide and 20 MP zoom cameras. H30T has 48 MP wide and 40 MP zoom cameras and adds a near-infrared auxiliary light. | |
| Surface temperatures | H20T scene ranges are −40 to 150 °C in high gain and −40 to 550 °C in low gain. Unfiltered H30T measures −20 to 150 °C in high gain and 0 to 600 °C in low gain. | |
| Environmental limits | H20T is IP44 and H30T is IP54. Both specify ambient operation from −20 to 50 °C. H20T temperature measurement requires ambient conditions from −10 to 50 °C. | |
| Payload mass | H20T weighs 828 ± 5 g. H30T weighs 920 ± 5 g. | |
| Host aircraft | H20T is listed for M300 RTK and M350 RTK. H30T is listed for both and for Matrice 400. On M300 RTK, H30T requires DJI RC Plus. |
Send this list as it is and get one price for every part.
Quote the full parts list →The H30T records twice as many native thermal pixels across the frame and twice as many down it. That gives an analyst more samples to inspect, but the number falling on a particular component also depends on framing, focus and distance. Start with an image from a job that required a repeat visit. Mark the detail the engineer could not resolve and ask for a comparison of that same detail from an approved observation position.
Decide which camera changes the maintenance report
For recurring roof inspections, the H20T can be a practical replacement purchase if technicians can consistently locate a suspect area in both the thermal image and the visible overview. Retrieve an older report and ask the technician to identify the roof section, nearby fixtures and the area to examine on foot. If that exercise succeeds with H20T files, a same-model replacement preserves a familiar reference for the next visit. Establish the availability of repair service before assigning that unit to a long contract.
For smaller components on industrial equipment, evaluate the H30T with the inspector who writes the findings. Capture a wide view for orientation, a visible detail and a thermal still. Have the inspector mark the suspect component and an adjacent component on the original thermal grid. Check whether their boundaries remain distinct when the report is printed or exported. If the extra pixels resolve a feature that previously shared its reading with the background, the buyer has a specific reason to upgrade.
The zoom camera also affects how easily someone can associate a thermal observation with the correct asset. DJI gives the H20T a 20 MP zoom camera and the H30T a 40 MP zoom camera. Try reading an equipment label or identifying a bolted cover on an approved training asset from the usual inspection position. Look at the saved file under ordinary site lighting. A large zoom value on a controller display is a poor acceptance criterion unless the engineer can identify the correct component afterward.
Specify the temperature range and measurement mode
Begin with the expected surface temperatures and the tolerances in the client's report. The H20T data sheet gives scene ranges for its high and low gain settings. DJI also lists a narrower ambient operating interval for taking temperature measurements than for powering the payload. A winter inspection brief should state the expected air temperature as well as the surface temperatures of interest. Have the thermographer review both before accepting a configuration on the strength of a single maximum figure.
For the H30T, the optional Infrared Density Filter changes the available range and the quality of the received signal. It is relevant to work on very hot industrial surfaces. DJI specifies a low-gain maximum of 600 °C without it and 1600 °C with it. The filter reduces the infrared signal reaching the sensor, and DJI gives substantially wider measurement tolerances with the filter fitted. Ask the process engineer whether those tolerances are acceptable at the temperatures that trigger a maintenance decision.
Need a quote for this? Tell us what you need →
The H30T also has a High-Res mode for viewing subtle temperature differences. Temperature measurement is unavailable in that mode. For a contract requiring a numerical finding, request a second sample captured in a measurement mode and have the analyst recover the reading from the original file. Make the required gain, filter state and measurement area part of the inspection record. That gives the next analyst enough information to compare a follow-up visit with the first observation.
Check the aircraft, controller and accessories together
Record every airframe the payload will serve. DJI lists H20T support on Matrice 300 RTK, and the Matrice 350 RTK compatibility list includes both H20T and H30T. H30T also works with Matrice 300 RTK when paired with DJI RC Plus. An older M300 kit can therefore need a controller purchase as well as a camera. Ask for a demonstration on the organization's own controller and aircraft, with the proposed firmware versions recorded alongside the payload serial number.
For a Matrice 400 deployment, DJI lists H30T among the supported gimbal cameras. Its published compatibility list omits H20T. If a camera must rotate between a 350 and a 400, put both host combinations on the acceptance sheet. Test the actual gimbal connector and mounting position planned for each aircraft, particularly if the crew also carries another payload. Allow space in the case for the detached camera, its protective cover and any filter in a clearly identified holder.
Weigh the configured aircraft before assessing its working time. The H30T is about 92 g heavier than the H20T on DJI's nominal figures. The effect on a route depends on the aircraft, other equipment and conditions at the site. Time a normal inspection with the intended battery reserve and record when the last usable image was captured. A payload mass comparison alone cannot supply an endurance estimate for an aircraft that carries several accessories.
Accept the data workflow and service terms
Both cameras save radiometric thermal stills as R-JPEG files. For H30T, DJI identifies version 3.3.0 or later of DJI Thermal Analysis Tool 3 for processing them. Give original samples to the person who manages the inspection archive. Ask that person to open a file, select a measurement area, document the value and export the result with its visible reference image. Repeat the exercise on the workstation that will be used after deployment, including any restrictions the organization places on software installation.
A mixed fleet creates a particular issue for long-term records. The next inspector may open an older H20T report beside a new H30T report with a different view and more pixels. Preserve the original stills, the gain setting, the observed surface and the measurement location with each report. Agree on a visible reference feature that survives routine maintenance. This allows a reviewer to compare the same part of a housing across visits even if a camera or operator has changed.
The H30 series succeeds the H20 series in this payload family. DJI's reviewed public service notice gives no H20T end-of-service date. For a replacement or stored unit, ask for its condition, warranty eligibility, repair route and the history of any gimbal or sensor work. During acceptance, inspect the lens windows, exercise the gimbal and review a radiometric file from the actual serial number. A recording from another unit demonstrates the model's capabilities but leaves the condition of the offered camera unresolved.
For an itemized enquiry, send our team the aircraft and controller models, intended mounting position, typical surface temperatures, smallest feature the report must resolve and analysis software in use. Include a redacted example of a difficult inspection if available. Those details let the supplier identify the camera, filter and controller combination to demonstrate and give the receiving team a concrete result against which to check the shipment.
Frequently asked questions
Is the H30T thermal image enlarged from a smaller detector?
DJI confirms that 1280 × 1024 is the native sensor resolution. Compare the saved stills at the distance and framing your reports require.
Can we upgrade an M300 RTK by ordering the H30T alone?
Check the controller first. DJI requires RC Plus for this combination, so a kit with a different controller needs an updated configuration.
When does the H30T reach 1600 °C?
That upper limit requires the optional Infrared Density Filter and low gain. Review filtered measurement tolerances with the engineer who sets the acceptance threshold.
Can High-Res mode deliver a temperature reading?
H30T uses this mode to visualize low-contrast thermal detail. Select a measurement-capable gain mode for a numerical report.
Which payload can move to a Matrice 400?
DJI lists H30T for Matrice 400. Specify the host and connector on the order and verify them with the payload during acceptance.