ChinaDroneRequest a quote →

DJI Air 3S vs DJI Air 3: Procurement Guide

Updated · 8 min read

Compare DJI Air 3S and DJI Air 3 cameras, sensing, storage, controllers, and shared accessories for single-aircraft and fleet orders.

Choose DJI Air 3S when the work calls for a larger wide-camera sensor, forward LiDAR, more built-in storage, or 4K slow motion at 120 fps. DJI Air 3 remains a practical option for daylight production and fleet expansion where the existing camera output passes review and the team already has working kits. Both models offer a wide view and a medium telephoto view. The upgrade decision depends on how often the crew uses the wide camera in difficult light, what it needs from the sensing system, and how much equipment it can carry over.

Compare the aircraft and their standard kits

DJI Air 3S and DJI Air 3 procurement comparisonDJI's endurance values are test maxima. The listed high frame rates refer to slow-motion capture.
PartWhat to look forMatching products
Wide cameraAir 3S has a 1-inch, 50 MP CMOS sensor and a 24 mm-equivalent f/1.8 lens. Air 3 has a 1/1.3-inch, 48 MP CMOS sensor and a 24 mm-equivalent f/1.7 lens.
Medium telephotoBoth list a 1/1.3-inch, 48 MP CMOS sensor and a 70 mm-equivalent f/2.8 lens.
Video workflowBoth support 10-bit D-Log M, HLG, and 2.7K vertical video. Air 3S captures 4K slow motion at up to 120 fps. Air 3 captures it at up to 100 fps.
Obstacle sensingBoth have omnidirectional binocular vision and a downward infrared sensor. Air 3S also has forward-facing LiDAR.
Takeoff weight and enduranceAir 3S is rated at 724 g and up to 45 minutes. Air 3 is rated at 720 g and up to 46 minutes.
Transmission and storageBoth use O4 with live view up to 1080p/60. Air 3S has 42 GB of internal storage and Air 3 has 8 GB.
Battery energyAir 3S standard battery is 62.5 Wh. Air 3 standard battery is 62.6 Wh.

Send this list as it is and get one price for every part.

Quote the full parts list →

Read the endurance figures with the manufacturer's test conditions attached. DJI lists 45 minutes for Air 3S and 46 minutes for Air 3 under distinct windless forward-flight test setups. Neither figure describes a normal sortie with a landing reserve. To compare the aircraft for scheduling, run the same approved route with each, using the same landing policy and comparable conditions. Record the time available for filming after takeoff, repositioning, and return. A familiar charging routine and a full set of healthy packs may matter more to a shift than the difference between the published figures.

Both aircraft use DJI O4 and support controller live view up to 1080p at 60 fps. Check the destination market and the operating environment before using wireless specifications in a tender. For a repeatable evaluation, have operators set up at a representative authorized site and check the live image, controller readability, and handover process. The operator's live image serves a different purpose from the video file delivered to the editor.

Match the camera and sensing changes to the work

For daylight real estate, tourism, or site documentation, compare a wide establishing shot and a medium telephoto detail on both aircraft. Their 24 mm- and 70 mm-equivalent views support similar framing from the same position. Decide whether the existing Air 3 output meets the client's delivery format before changing aircraft and retraining staff. If you regularly switch cameras during one flight, give the editor paired files and check how much work it takes to match the shots in the finished sequence.

Prioritize Air 3S for evaluation if crews often shoot wide views at dawn or dusk or deliver footage with substantial grading. Its larger wide sensor is the meaningful hardware difference for that use. The medium telephoto camera retains the same stated sensor format, pixel count, focal-length equivalent, and aperture as Air 3. Compare real files from both cameras before drawing conclusions about whether those matching headline specifications translate to matching output. Use the exposure, motion, and contrast levels the team actually sees on location.

Both aircraft offer 10-bit D-Log M and HLG and support 2.7K vertical video. Air 3S raises the published 4K slow-motion recording rate to 120 fps from 100 fps on Air 3. The respective high-rate files are prepared for slow-motion playback. Check that the editor can ingest and deliver the chosen files, particularly when a client requests a specific playback cadence. Ask for original footage from the exact mode so the editor can check the actual files and how they play back.

Air 3S adds forward-facing LiDAR to the all-direction vision system. It is relevant if lower-light sensing is part of the purchasing brief. The LiDAR points forward, while the vision system still has lighting and surface conditions. Establish an approved route and a clear response to degraded sensing before flying in low light. Use a planned demonstration to review what the controller reports and what the crew must do when sensing is limited. The aircraft's safety features are one part of the operating plan.

Check what can move between kits

DJI documents Air 3 low-noise propellers, the Air 3 Battery Charging Hub, and the Air 3 Intelligent Flight Battery for use with Air 3S. The original Air 3 battery can power Air 3S, with Off-State QuickTransfer unavailable in that configuration. DJI also lists its Air 3S battery for use in Air 3 and lists both pack types for the Air 3 Series hub. For a mixed fleet, request exact part numbers and run an acceptance check with each intended aircraft, pack, and hub combination. Label pack generations if transfer while the aircraft is off is an operating requirement.

Need a quote for this? Tell us what you need →

Both models have a DJI RC 2 option. The standard phone-controller configurations are RC-N3 with Air 3S and RC-N2 with Air 3. DJI also lists RC-N3 support for Air 3. Check the proposed pairing and firmware on the actual kit, especially for aircraft-only orders or mixed lots. Include the phone cable and validate the organization's handsets for phone-controller kits. For screen-controller kits, check the workflow for assignment, activation, and updating across crews.

Order the ND filters for the named airframe. DJI lists distinct sets for Air 3 and Air 3S. Obtain an itemized list for each offer, with batteries, charger and hub, filters, spare propellers, cable, storage media, and case identified. Air 3S has 42 GB of built-in storage compared with 8 GB in Air 3. That extra space can cover a forgotten card or a short assignment, depending on the recording mode. For routine production, qualify the microSD card and the file-copy workflow that operators will use in the field.

Compare the cost of standardizing the fleet

Map out which aircraft can share a pool of spares and which parts need dedicated bins. A mixed Air 3 and Air 3S fleet can share some power and propeller equipment, while filters and a feature such as Off-State QuickTransfer still depend on specific parts. If jobs run in parallel, count batteries and hubs per crew and define where they will recharge between assignments. Ask for one complete packing list for each team and another for shared stock. That makes it easier to see where a nominally compatible accessory would need to be duplicated because several crews need it at the same time.

Confirm destination, battery transport, and acceptance

Record the market, exact bundle, warranty and service region, and any airframe marking on the purchase order. DJI lists both models as C1 for the EU. Verify the actual unit and the relevant declaration before accepting imported or mixed-region stock. If the aircraft will be reassigned across borders, confirm the configuration at the new destination as part of the transfer. Keep records for the airframe and controller separately so their origin and support coverage can be checked later.

DJI lists 62.5 Wh for the Air 3S pack and 62.6 Wh for the Air 3 pack. Use the exact pack label and shipping count. Tell the forwarder which batteries are in equipment, packed with it, or shipped separately. Confirm carrier acceptance, packing and terminal protection, and obtain the requested test documentation for the battery model and route. If a crew is flying commercially with spare packs, have the travel coordinator check the airline's baggage instructions for those packs in advance.

Define which files the supplier should hand over with the equipment, including an example from each camera and a copy of the final packing list. Use that list when checking replacements, especially if different teams receive different controller or filter combinations.

At delivery, verify the order contents and pair the controller. Capture both focal lengths, test each intended battery type, copy clips through the planned process, and record the firmware and accessory models. For larger orders, run those checks on a sample kit before approving the rest. Contact our team with the destination, intended footage, controller inventory, battery stock, and the number of ready-to-deploy kits you need.

Frequently asked questions

Which model is better for low-light wide shots?

Air 3S is the first to evaluate for that brief because its wide camera uses a larger sensor. Review original footage from both in the light and delivery format you expect.

Does Air 3S offer a new focal length?

Both models offer 24 mm- and 70 mm-equivalent cameras. Air 3S changes the wide-camera sensor format while retaining those focal-length equivalents.

Can I use an Air 3 battery in Air 3S?

Yes. DJI supports the pairing. Air 3S loses Off-State QuickTransfer with an Air 3 battery installed.

Can we keep a DJI RC 2 when adding an Air 3S?

DJI lists RC 2 for both models. Verify firmware, pairing, and your organization's controller assignment process before placing aircraft-only orders.

Can the same ND filters serve both fleets?

Order filters for each aircraft model. DJI lists separate Air 3 and Air 3S sets.