CubePilot Here4 vs Holybro H-RTK F9P: Procurement Guide
Compare Here4 with original and updated Holybro F9P rovers by correction bands, installed mass, interface, update rate and base-station requirements.
Choose CubePilot Here4 for a build that already uses DroneCAN and needs a light rover with an integrated antenna. Choose the Holybro H-RTK F9P configuration by its job and connector. A serial rover can make sense on an aircraft with a free GPS port, while a kit for establishing a local reference needs a receiver and antenna intended for ground use. The name F9P alone leaves all three decisions open. Before comparing offers, put the aircraft, carrier board and correction source on the same equipment list.
Compare the receivers that would actually ship
| Part | What to look for | Matching products |
|---|---|---|
| Receiver and GPS bands | Here4 uses NEO-F9P with L1/L5. Holybro's ZED-F9P receivers here use L1/L2. | |
| RTK navigation updates | Here4 up to 20 Hz. Holybro Rover Lite and updated Rover up to 8 Hz. | |
| Published mass | Here4 is 60 g with cable. Holybro lists 106 g for Rover Lite and 117 g for the updated Rover. | |
| Aircraft interface | Here4 uses DroneCAN. Original standard Rover Lite uses UART. Updated Rover is available in UART or DroneCAN versions. | |
| Reference hardware | CubePilot lists Here4 Base separately. Holybro's original Helical can be rover or base. Its Base is ground-only. |
Send this list as it is and get one price for every part.
Quote the full parts list →The Holybro name covers several assemblies. The original Standard F9P UART family includes Rover Lite for vehicle use, Helical for rover or base service, and Base for a fixed reference. Holybro subsequently introduced the H-RTK ZED-F9P Rover as an update to its original UART and DroneCAN rovers. That change matters when replacing a damaged unit from an older kit. The revised rover has an RM3100 compass and omits the earlier safety switch, internal buzzer and dedicated fix indicator. A workshop that relies on the old switch or indication should review that change before accepting a substitution.
Here4 combines a u-blox NEO-F9P with a dual-band antenna in one housing. Its GPS bands are L1 and L5. Holybro specifies GPS L1 and L2 for the receivers compared here. Ask the correction provider which signals its reference equipment observes and which messages the service supplies at the intended site. A shared constellation name on two data sheets tells the buyer little about which observations the base and rover can use together. A trial with the intended correction stream resolves a question that a receiver-only demonstration leaves open.
Choose for a survey aircraft, a retrofit or a ground station
For a new mapping aircraft, compare complete installed assemblies. CubePilot quotes 60 g for Here4 with its cable. Weigh the bracket, fasteners and any extension along with the receiver when checking the payload budget. Have the survey crew collect a short sample over independently checked points and process it with their normal software. An RTK fix describes a navigation solution at the antenna. The deliverable also depends on where the antenna sits relative to the camera, when exposures are recorded and how the images are processed.
For a retrofit, start with the existing wiring drawing. A spare serial GPS port gives a reason to evaluate a Holybro UART rover. A populated serial interface and an available CAN connection may favor Here4 or the four-pin DroneCAN version of the updated Holybro rover. Ask the maintainer who will service the aircraft which option they can diagnose with the equipment they already carry. Replacing a cable at a remote site is much easier when both the correct spare and a diagram of its two ends are in the case.
For a team that needs a ground reference, request a separate line for the base. Holybro's Helical can take either role, which may suit a workshop that reassigns equipment between projects. Its Base assembly includes a separate antenna and an antenna cable, useful when the receiver needs to stay near the ground computer. CubePilot documents a separate Here4 Base product. Specify the reference antenna, support, connection to the ground computer and means of getting corrections to the aircraft in either quotation. Assign an owner to each piece if two crews share the station.
Check electrical and mechanical compatibility
List the receiver's full part number next to the carrier-board revision. On the updated Holybro rover, 12054 denotes a ten-pin UART cable, 12058 a six-pin UART cable and 12059 a four-pin DroneCAN cable. On the original Rover Lite, Holybro specifically cautions that its standard ten-pin GPS1 connector is incompatible with CubePilot. Check the drawing for the actual carrier and harness before ordering an adapter. Cable length, strain relief and access to the connector after fitting the cover all belong in the trial installation.
Need a quote for this? Tell us what you need →
Ask the integrator to account for receiver power with the other peripherals connected. For the updated Holybro rover, the published figures are 4.75 to 5.25 V and about 250 mA. Have the workshop identify the supply and confirm the available current on the chosen port. On Here4, check the carrier's CAN support and proposed bus layout against the manufacturer's manual. For both choices, record the approved firmware versions and save the receiver identification shown by the flight controller alongside the build record.
The update-rate figures also deserve a line on the acceptance sheet. CubePilot lists RTK navigation updates up to 20 Hz. Holybro lists up to 8 Hz for RTK on the compared units and gives a separate maximum for raw data. If a payload needs a particular position cadence, ask for a timestamped log from the application that consumes it. Review the spacing of messages during a representative recording as well as the average rate. That gives the integration engineer evidence about the whole chain from antenna to saved file.
Make repeatability part of acceptance
Set aside a known point in clear sky for the initial comparison. Record its coordinate reference system, the antenna height convention and the source of its coordinates. Have each crew set up independently and save the observed position, fix state and correction age. A repeat visit on a different day helps expose differences in how crews place the antenna or enter the reference coordinates. Keep the observations with the equipment record so a later replacement can be assessed against the same reference.
For a crew using a network reference, distinguish the receiver purchase from the ongoing correction service. Ask who holds the account and how another operator gains access when the usual ground computer is unavailable. For a crew using its own base, include a record of the reference position with the job files. If a second survey starts from a different reference position, a consistent offset between the two results can survive even when both logs show a fixed solution.
Next, repeat the check under conditions typical of the intended work. A test beside a building may produce a different result from one in an open field. Agree in advance on the tolerated horizontal and vertical error and how much of the recording must meet it. Include a check of what the operator sees when corrections become unavailable and when service resumes. Run that portion with the receiver stationary. It lets the crew review the indications and saved data without introducing changes in aircraft motion.
For a multi-aircraft purchase, count complete systems per simultaneous job. Two rovers can be ready at the workshop while the only ground antenna is away with another crew. Name the shared assets, the site at which they will be available, and who maintains the correction subscription if one is required. For legacy spares, request a photograph of the label and confirmation of the installed compass, harness and controls. Ask separately about repair coverage and replacement stock for that revision.
Keep one accepted assembly available as a workshop reference. Photograph its mounting orientation, note which harness was used and retain a short log with the accepted configuration. When the next batch arrives, the receiving technician can identify a changed cable or receiver revision before it reaches an aircraft. For a model-specific quotation, send our team the carrier-board model, open ports, acceptable installed mass, correction source and the number of simultaneous rover and base positions.
Frequently asked questions
Can a Here4 replace a serial rover on the same lead?
Here4 uses DroneCAN. Identify a supported CAN port and matching harness on the carrier before specifying the replacement.
Which Holybro part should go on a tripod?
The Base assembly is intended for a reference station. Helical can also serve as a base. Rover Lite is an aircraft rover.
Does the updated Holybro rover keep the safety switch?
Holybro removed it in the revision. Review any crew procedure that depends on the switch or the earlier dedicated fix indicator.
Does an F9P base automatically match either rover?
Check the common signals and correction messages and test the proposed pairing. Here4 and the Holybro receivers compared here use different second GPS bands.
What should a survey crew retain after acceptance?
Keep the hardware revision, cable identification, firmware versions, reference coordinates and a log from a known point. These give the workshop a repeatable replacement check.